AMIK 100 Three Phase Digital Panel Meter

Amik 100 is a compact multifunction instrument which measures important electrical parameters in 3 phase 4 Wire and 3 phase 3 Wire Network & replaces multiple analog panel meters

Application

Amik 100 measures important electrical parameters in 3 phase 4 Wire and 3 phase 3 Wire Network & replaces the multiple analog panel meters. It measures electrical parameters like AC Voltage, AC Current, & many more.
 

 

Sr No	Parameter	3 Phase 4 Wire	3 Phase 3 Wire	1 Phase 2 Wire
1	System Volts
2	System Current
3	Frequency
4	Volts R–N		X
5	Volts Y–N		X	X
6	Volts B–N		X	X
7	Volts R-Y			X
8	Volts Y–B			X
9	Volts B–R			X
10	Current R
11	Current Y			X
12	Current B			X
13	RPM
14	Max (System Voltage / System Current)
15	Min (System Voltage / System Current)
16	Hour Run
17	ON Hour
18	Number of auxiliary interrupt

 

 

On site programmable PT/CT ratios	It is possible to program primary of the external potential Transformer (PT), primary of external Current Transformer (CT) on site via front panel keys by entering into Programming mode.
User selectable CT Secondary 5A / 1A	The secondary of external Current Transformer (CT) can be programmed on site to either 5A or 1A using front panel keys.
User selectable PT Secondary	The secondary of external Potential Transformer (PT) can be programmed on site from 100VLL to 500VLL using front panel keys.
User selectable 3 phase 3Wire 4Wire or Single phase Network	User can program on site the network connection as either 3 Phase 3 Wire/4 Wire or single phase network using front panel keys. In case of self powered configuration either 3 Phase 4 wire or single phase network are available.
RPM Measurement	The instrument display Rotation per minutes for generator applications. Number of poles can be set on site depending upon application requirement.
Limit switch (Relay)	The instrument will trip the relay if the programmed parameter exceeds the programmed Trip Limits.
3 line 4 digits LED display	Simultaneous display of 3 Parameters.
Enclosure Protection for dust and water	Conforms to IP 50 (for front face) or IP 65 option (for front with seal) & IP 20 (for back) & as per IEC60529.
Storage of parameters possible	The instrument stores minimum and maximum values for System Voltage, System Current, Run Hour, ON Hour & number of Interrupts. Every 60 sec stored values are updated.
Four function keys	Using the four function key, it is possible to go desired parameter screen instantly.
Onsite selection of Auto scroll / Fixed Screen	User can set the display in auto scrolling mode or fixed screen mode using front panel keys.
Low back depth	The instrument has very low back depth (behind the panel) of less than 55mm (without output options).
True RMS measurement	The instrument measures distorted waveform up to 15th Harmonic.
EMC Compatibility	Compliance to International standard IEC 61326
Interference Emission	IEC 61326-1 : 2005, Class, A
Interference Immunity	IEC 61326-1 : 2005
Electrostatic discharge	IEC 61000-4-2 -- 4kV/8kV contact/air. (ESD)
EM Field	IEC 61000-4-3 -- 10 V/m (80 MHz to 1 GHz) – 3 V/m (1.4 Ghz to 2 GHz) -- 1 V/m (2 GHz to 2.7 GHz)
Burst	IEC 61000-4-4 -- 2 kV (5/50 ns, 5 kHz)
Surge	IEC 61000-4-5 -- 1 kVLL / 2 kVLN.
Conducted RF	IEC 61000-4-5 -- 3 V (150 kHz to 80 MHZ)
Rated Power Frequency magnetic Field	IEC 61000-4-8 -- 30 A/m
Voltage dip	IEC 61000-4-1 40% during 10/12 cycles. 70% during 25/30 cycles.
Short interruptions	IEC 61000-4-11 0% during 25/30 cycles. 25 cycles for 50 Hz test. 30 cycles for 60 Hz test.

   

With optional Limit switch

     

Easy Clip in Installation on Panel
Rear Connection

     

	Self Powered Aux	External Powered Aux
3 Phase 4 Wire Unbalanced Load
3 Phase 3 Wire Unbalanced Load	Not Applicable
1 Phase 2 Wire
*Note: For Measurement of parameters, Voltage must be present between terminal 2 & 11 for single phase or 3 phase 4 wire network and between terminal 2 & 5 or 2 & 8 for 3 phase 3 wire network.