| Sample |
| Sample Mode |
Real-time Sample |
| Real-time Sample Rate |
Analog channel:
1 GSa/s (single-channel), 500 MSa/s (dual-channel), 250 MSa/s (three/four-channel)
Digital channel:
1 GSa/s (8-channel), 500 MSa/s (16-channel) |
| Peak Detect |
Analog channel: 4 ns Digital channel: 4 ns |
| Averaging |
After all the channels finish N samples at the same time, N can be 2, 4, 8, 16, 32, 64, 128, 256, 512 or 1024 |
| High Resolution |
12 bit (max.) |
| Interpolation |
Sin(x)/x (optional) |
| Minimum Detect Pulse Width |
Digital channel: 10 ns |
| Memory Depth |
Analog channel: standard 12 Mpts (single-channel), 6 Mpts (dual-channel), 3 Mpts (three/four-channel); optional 24 Mpts (single-channel), 12 Mpts (dual-channel), 6 Mpts (three/four-channel)
Digital channel:
standard 12 Mpts (8-channel), 6 Mpts (16-channel); optional 24 Mpts (8-channel), 12 Mpts (16-channel) |
| Input |
| Number of Channels |
MSO1XX4Z/1XX4Z-S: 4 analog channels, 3 analog channels+8 digital channels, 2 analog channels+16 digital channels
DS1XX4Z Plus/1XX4Z-S Plus: 4 analog channels, MSO upgradable
DS1054Z: 4 analog channels |
| Input Coupling |
DC, AC or GND |
| Input Impedance |
Analog channel:(1 MΩ±1%) || (15 pF±3 pF)
Digital channel:(100 MΩ±1%) || (8 pF±3 pF) |
Probe
Attenuation
Coefficient |
Analog channel:0.01X-1000X, 1-2-5 step |
| Maximum Input Voltage (1MΩ) |
Analog channel: CAT I 300 Vrms, CAT II 100 Vrms, transient overvoltage 1000 Vpk With RP2200 10:1 probe: CAT II 300 Vrms
Digital channel: CAT I 40 Vrms, transient overvoltage 800 Vpk |
| Horizontal |
| Time Base Scale |
5 ns/div to 50 s/div |
| Maximum Record Length |
24 Mpts (optional) |
| Time Base Accuracy [1] |
≤ ± 25 ppm |
| Clock Drift |
≤ ± 5 ppm/Year |
| Maximum Delay Range |
Negative delay: 1/2 (Memory Depth/Sample Rate)
Positive delay: 1 s to 500 s |
| Time Base Mode |
YT, XY, Roll |
| Number of X-Ys |
1 path |
| Waveform Capture Rate [2] |
30,000 wfms/s (dots display) |
| Zero Offset |
±0.5div*minimum time base scale |
| Vertical |
| Bandwidth (-3dB) |
MSO1104Z/1104Z-S and DS1104Z Plus/1104Z-S Plus: DC to 100 MHz
MSO1074Z/1074Z-S and DS1074Z Plus/1074Z-S Plus: DC to 70 MHz
DS1054Z: DC to 50 MHz |
| Single-shot Bandwidth |
MSO1104Z/1104Z-S and DS1104Z Plus/1104Z-S Plus: DC to 100 MHz
MSO1074Z/1074Z-S and DS1074Z Plus/1074Z-S Plus: DC to 70 MHz
DS1054Z: DC to 50 MHz |
| Vertical Resolution |
Analog channel: 8 bits
Digital channel: 1 bit |
| Vertical Scale |
1 mV/div to 10 V/div |
| Offset Range |
1 mV/div to 499 mV/div: ± 2 V
500 mV/div to 10 V/div: ± 100 V |
| Bandwidth Limit1 |
20 MHz |
Low Frequency Response
(AC coupling, -3dB) |
≤5 Hz (on BNC) |
| Calculated Rise Time [1] |
MSO1104Z/1104Z-S and DS1104Z Plus/1104Z-S Plus: 3.5 ns
MSO1074Z/1074Z-S and DS1074Z Plus/1074Z-S Plus: 5 ns
DS1054Z: 7 ns |
| DC Gain Accuracy [3] |
<10 mV: ±4% full scale
≥10 mV: ±3% full scale |
| DC Offset Accuracy |
±0.1 div ± 2 mV ± 1% offset |
Channel to Channel
Isolation |
DC to maximum bandwidth: >40 dB |
| Vertical (Digital Channel)(Applicable to MSO1000Z and DS1000Z Plus with MSO Upgrade Option) |
| Threshold |
Adjustable threshold of 8 channels per group |
| Threshold Selection |
TTL (1.4 V)
5.0 V CMOS (+2.5 V), 3.3 V CMOS (+1.65 V)
2.5 V CMOS (+1.25 V), 1.8 V CMOS (+0.9 V)
ECL (-1.3 V)
PECL (+3.7 V)
LVDS (+1.2 V)
0 V
User |
| Threshold Range |
±15.0 V, in 10 mV step |
| Threshold Accuracy |
±(100 mV + 3% of threshold setting) |
| Dynamic Range |
±10.0 V + threshold |
| Minimum Voltage Swing |
500 mVpp |
| Vertical Resolution |
1 bit |
| Trigger |
| Trigger Level Range |
±5 div from the center of the screen |
| Trigger Mode |
Auto, Normal, Single |
| Holdoff Range |
16 ns to 10 s |
High Frequency
Rejection |
75 kHz |
Low Frequency
Rejection |
75 kHz |
| Trigger Sensitivity [1] |
1.0div (below 5mV or noise rejection is enabled)
0.3div (above 5mV and noise rejection is disabled) |
| Edge Trigger |
| Edge Type |
Rising, Falling, Rising&Falling |
| Pulse Trigger |
| Pulse Condition |
Positive Pulse Width (greater than, lower than, within specified interval)
Negative Pulse Width (greater than, lower than, within specified interval) |
| Pulse Width Range |
8 ns to 10 s |
| Runt Trigger |
| Pulse Condition |
None, > (greater than), < (lower than), <> (within the specified interval) |
| Polarity |
Positive, Negative |
| Pulse Width Range |
8 ns to 10 s |
| Windows Trigger |
| Windows Type |
Rising, Falling, Rising&Falling |
| Trigger Position |
Enter, Exit, Time |
| Windows Time |
8 ns to 10 s |
| Nth Edge Trigger |
| Edge Type |
Rising, Falling |
| Idle Time |
16 ns to 10 s |
| Number of Edges |
1 to 65535 |
| Slope Trigger |
| Slope Condition |
Positive Slope (greater than, lower than, within specified interval)
Negative Slope (greater than, lower than, within specified interval) |
| Time Setting |
8 ns to 10 s |
| Video Trigger |
| Signal Standard |
Support standard NTSC, PAL and SECAM broadcasting standards
Support 480P, 576P HDTV standards |
| Pattern Trigger |
| Pattern Setting |
H, L, X, Rising Edge, Falling Edge |
| Delay Trigger |
| Edge Type |
Rising, Falling |
| Delay Type |
> (greater than), < (lower than), <> (within the specified interval), >< (outside the specified interval) |
| Delay Time |
8 ns to 10 s |
| TimeOut Trigger |
| Edge Type |
Rising, Falling, Rising&Falling |
| TimeOut Value |
16 ns to 10 s |
| Duration Trigger |
| Pattern Setting |
H, L, X |
| Trigger Condition |
> (greater than), < (lower than), <> (within the specified interval) |
| Duration Time |
8 ns to 10 s |
| Setup/Hold Trigger |
| Edge Type |
Rising, Falling |
| Data Pattern |
H, L,X |
| Setup Time |
8 ns to 1 s |
| Hold Time |
8 ns to 1 s |
| RS232/UART Trigger |
| Polarity |
Normal, Invert |
| Trigger Condition |
Start, Error, Check Error, Data |
| Baud |
2400 bps, 4800 bps, 9600 bps, 19200 bps, 38400 bps, 57600 bps, 115200 bps, User |
| Data Bits |
5 bits, 6 bits, 7 bits, 8 bits |
| I2C Trigger |
| Trigger Condition |
Start, Restart, Stop, Missing Ack, Address, Data, A&D |
| Address Bits |
7 bits, 8 bits, 10 bits |
| Address Range |
0x0 to 0x7F, 0x0 to 0xFF, 0x0 to 0x3FF |
| Byte Length |
1 to 5 |
| SPI Trigger |
| Trigger Condition |
TimeOut, CS |
| Timeout Value |
16 ns to 10 s |
| Data Bits |
4 bit to 32 bit |
| Data Line Setting |
H, L, X |
| Measure |
Manual mode | Voltage deviation between cursors (ΔV)
Time deviation between cursors (ΔT)
Reciprocal of ΔT (Hz) (1/ΔT)
Track mode | Voltage and time values of the waveform point
Auto mode | Allow to display cursors during auto measurement |
| Auto Measurement |
Measurements of Maximum, Minimum,
Peak-Peak Value, Top Value, Bottom Value,
Amplitude, Average, Mean Square Root,
Overshoot, Pre-shoot, Frequency, Period, Rise
Time, Fall Time, Positive Pulse Width, Negative
Pulse Width, Positive Duty Cycle, Negative
Duty Cycle, Delay A~B , Delay A~B , Phase
A~B , Phase A~B |
Number of
Measurements |
Display 5 measurements at the same time |
Measurement
Range |
Screen Region or Cursor Region |
Measurement
Statistic
Counter |
Average, Max, Min, Standard Deviation
Number of Measurements
Hardware 6 bits counter (channels are
selectable) |
| Math |
| Waveform |
A+B, A-B, A×B, A/B, FFT, A&&B, A||B, A^B, !A, Intg, Diff, Sqrt, Lg, Ln, Exp, Abs, Filter |
| FFT Window |
Rectangle, Hanning, Blackman, Hamming,Flat Top,Triangle |
| FFT Mode |
Trace, Memory |
| FFT Display |
Half, Full |
| FFT Vertical Scale |
dB/dBm, Vrms |
| Filter |
Low Pass Filter, High Pass Filter, Band Pass Filter, Band Stop Filter |
Number of Buses
for Decoding |
2 |
| Decoding Type |
Parallel (standard), RS232/UART (option), I2C (option), SPI (option) |
| Display |
| Display Type |
7.0 inches TFT LCD display |
| Display Resolution |
800 horizontal×RGB×480 vertical pixel |
| Display Color |
16 million color (24 bit true color) |
| Persistence Time |
Min, 50 ms, 100 ms, 200 ms, 500 ms, 1 s, 2 s, 5 s, 10 s, 20 s, Infinite |
| Display Type |
Dots, Vectors |
| I/O |
| Standard Ports |
USB HOST, USB DEVICE, LAN, Aux (TrigOut /PassFail) |
| Signal Sourse (DS1000Z-S) |
| Number of Channels |
2 |
| Sample Rate |
200 MSa/s |
| Vertical Resolution |
14 bits |
| Highest Frequency |
25 MHz |
| Standard Waveform |
Sine, Square, Pulse, Triangle, Noise, DC |
| Arbitrary Waveform |
Since, Exp.Rise, EXP.Fall, ECG, Gauss, Lorentz, Haversine |
| Sine |
Frequency Range |
0.1 Hz to 25 MHz |
| Flatness |
±0.5 dB (relative to 1 kHz) |
| Harmonic Distortion |
-40 dBc |
| Stray (Non-Harmonic) |
-40 dBc |
| Total Harmonic Distortion |
1% |
| Signal-to-Noise ration |
40 dB |
| Square/Pulse |
Frequency Range |
0.1 Hz to 15 MHz |
| Rise/Fall time |
<15 ns |
| Overshoot |
<5% |
| Duty Cycle |
10% to 90% |
| Duty Cycle Resolution |
1% to 10 ns (select the greater one) |
| Minimum Pulse Width |
20 ns |
| Pulse Width Resolution |
10 ns or 5 bits (select the greater one) |
| Jitter |
500 ps |
| Triangle |
Frequency Range |
0.1 Hz to 100 kHz |
| Linearity |
1% |
| Symmetry |
0 to 100% |
| Noise [1] |
Bandwidth |
25 MHz |
Internal Generated
waveforms |
Frequency Range |
0.1 Hz to 1 MHz |
| Arbitrary Waveforms |
Frequency Range |
0.1 Hz to 10 MHz |
| Waveform Length |
2 to 16k pts |
| Frequency |
Accuracy |
100 ppm (lower than 10 kHz)
50 ppm (greater than 10 kHz) |
| Resolution |
0.1 Hz or 4 bit, select the greater one |
| Amplitude |
Output Range |
20 mVpp to 5 Vpp, High-resistance
10 mVpp to 2.5 Vpp, 50 Ω |
| Resolution |
100 μV or 3 bit, select the greater one |
| Accuracy |
2% (1 kHz) |
| DC Offset |
Range |
±2.5 V, High-resistance
±1.25 V, 50 Ω |
| Resolution |
100 μV or 3 bit, select the greater one |
| Accuracy |
2% (1 kHz) |
| General Specifications |
| Probe Compensation Output |
| Output Voltage [1] |
About 3 V, peak-peak |
| Frequency [1] |
1 kHz |
| Power |
| Power Voltage |
100 V to 240 V, 45 Hz to 440 Hz |
| Power |
Maximum 50 W |
| Fuse |
2 A, T degree, 250 V |
| Environment |
| Temperature Range |
In operation: 0°C to +50°C
Out of operation: -40°C to +70°C |
| Cooling Method |
Fan |
| Humidity Range |
0° to +30°C : ≤95°C relative humidity
+35°C to +40°C : ≤75°C relative humidity
+40°C to +50°C : ≤45°C relative humidity |
| Altitude |
In operation: under 3,000 meters
Out of operation: under 15,000 meters |
| Mechanical |
| Dimensions [4] |
Width×Height×Depth =313.1 mm× 160.8 mm×122.4 mm |
| Weight [4] |
Without package | 3.2 kg ± 0.2 kg
With package | 3.8 kg ± 0.5 kg |
| Adjustment Interval |
| |
The recommended calibration interval is one year. |
| Regulation Standards |
| Electromagnetic |
2004/108/EC |
| Compatibility |
Execution standard EN 61326-1:2006 EN
61326-2-1:2006 |
| Safety |
UL 61010-1:2004; CAN/CSA-C22.2 NO.
61010-1-2004;
EN 61010-1:2001; IEC 61010-1:2001 |