| Model |
Single present |
FX4 |
FX6 |
FX4H |
— |
— |
| Dual present |
FX4-2P |
FX6-2P |
FX4H-2P |
FX4L-2P |
FX6L-2P |
| Totalizer (Indicator) |
FX4-I |
FX6-I |
FX4H-I |
FX4L-I |
FX6L-I |
| Digit |
4 Digit |
6 Digit |
4 Digit |
4 Digit |
6 Digit |
| Digit size |
W8×H14mm |
W4×H8mm |
W6×H10mm |
W8×H14mm |
| Power supply |
AC power |
100-240VAC 50/60Hz |
| AC/DC power |
12-24VAC 50/60Hz, 12-24VDC |
| Allowable voltage range |
90 to 110% of rated voltage |
| Power consumption |
AC power |
• Indicator type: Max. 6VA
• Single preset: Max. 7VA
• Dual preset: Max. 8VA (100-240VAC 50/60Hz) |
| AC/DC power |
• Indicator type: Max. 5.8VA
• Single preset: Max. 6.8VA
• Dual preset: Max. 7.6VA (12-24VAC 50/60Hz)
• Indicator type: Max. 2.7W
• Single preset: Max. 3.3W
• Dual preset: Max. 3.8W (12-24VDC) |
| Max. counting speed for CP1, CP2 |
Selectable 1cps/30cps/2kcps/5kcps by internal DIP switch |
| Min. input signal width |
RESET input |
Approx. 20ms |
| INHIBIT input |
| Input |
CP1, CP2 input (INHIBIT) |
Input logic is selectable
[Voltage input] Input impedance: 5.4kΩ, "H" level: 5-30VDC, "L" level: 0-2VDC
[No-voltage input] Impedance at short-circuit: Max. 1kΩ, Residual voltage at short-circuit: Max. 2VDC,
Impedance at open-circuit: Min. 100kΩ |
| RESET input |
| One-shot output time |
• Single preset type - 0.05 to 5sec.
• Dual preset type - 1st. output 0.5sec. fixed, 2st. output: 0.05 to 5sec. |
| Control output |
Contact |
Type |
Single preset type: SPDT (1c), Dual preset type: 1st output SPDT (1c), 2nd output SPDT (1c) |
| Capacity |
250VAC 3A at resistive load |
| Solid state |
Type |
Single preset: 1 NPN open collector
Dual preset: 1st output 1 NPN open collector, 2nd output 1 NPN open collector |
| Capacity |
30VDC Max. 100mA Max. |
| Memory protection |
Approx. 10 years (When using non-volatile semiconductor memory) |
| External sensor power |
12VDC±10% 50mA Max. |
| Environment |
Ambient temperature |
-10 to 55 °C, storage: -25 to 65 °C |
| Ambient humidity |
35 to 85%RH, storage: 35 to 85%RH |
| Insulation resistance |
Min. 100MΩ (at 500VDC megger) |
| Dielectric strength |
2000VAC 50/60Hz for 1 minute |
| Noise strength |
AC power |
±2kV the square wave noise (pulse width: 1㎲) by the noise simulator |
| DC power |
±500V the square wave noise (pulse width: 1㎲) by the noise simulator |
| *Environment resistance is rated at no freezing or condensation. |