|
Autonics BR Series General Specifications
*The model name with ‘-C’ is connector type.
|
| Sensing type |
Diffuse reflective |
Narrow beam reflectiv |
Retroreflective |
Through-beam |
| Sensing distance |
100mm*1 |
400mm*2 |
200mm*2 |
0.1 to 3m*3 |
4m / 20m |
| Sensing target |
Translucent, Opaque materials |
Opaque materials of min. ø60mm |
Opaque materials ofmin. ø15mm |
| Hysteresis |
Max. 20% at rated setting distance |
- |
| Response time |
Max. 1ms. |
| Power supply |
12-24VDC ±10%(Ripple P-P : Max. 10%) |
| Current consumption |
Max. 45mA |
| Light source |
Infrared LED(940nm) |
Infrared LED(850nm) |
Red LED(660nm) |
Infrared LED(850nm) |
| Sensitivity adjustment |
Adjustable(built-in the adjustment VR) |
Fixed |
| Operation mode |
Selectable Light ON or Dark ON by control cable(White) |
Dark ON |
Light ON |
| Control output |
NPN or PNP open collector output
- Load voltage: Max. 30VDC
- Load current: Max. 200mA
- Residual voltage - NPN: Max. 1V, PNP: Max. 2.5V
|
| Protection circuit |
Reverse polarity protection circuit, Output short-circuit protection circuit |
| Indicator |
Operation indicator : red LED
Power indicator : red LED(only for emitter of through-beam type) |
| Insulation resistance |
Min. 20MΩ(at 500VDC megger) |
| Noise resistance |
±240V the square wave noise(pulse width : 1μs) by the noise simulator |
| Dielectric strength |
1000VAC 50/60Hz for 1 minute |
| Vibration |
1.5mm amplitude or 300m/s2 at frequency of 10 to 55Hz(for 1 min.) in each of X, Y, Z directions for 2 hours |
| Shock |
500m/s2(approx. 50G) in each of X, Y, Z directions for 3 times |
| Environment |
Ambient illumination |
Sunlight : Max. 11,000lx
Incandescent lamp : Max. 3,000lx(Receiver illumination) |
| Ambient temperature |
-10 to 60°C, storage : -25 to 75°C |
| Ambient humidity |
35 to 85%RH, storage : 35 to 85%RH |
| Protection |
IP66(IEC standard) |
| Material |
• Case - BRP: PA(Black) / BR: Brass, Ni-plate
• Sensing part - PC |
• Case - BRP3M: PA(Black) / BR3M: Brass, Ni-plate
• Sensing part - Acrylic |
• Case - Brass, Ni-plate
• Sensing part - BR4M : Glass / BR20M : PC |
| Cable |
• BR(P): ø5, 4-wire, Length:2m(Emitter of through-beam type: ø5, 2-wire, Length: 2m / Receiver: ø5, 3-wire, Length: 2m) (AWG 22, Core diameter: 0.08mm, Number of cores : 60, Insulator out diameter: ø1.25)
• BR(P)-C: M12 connector |
| Accessory |
Individual |
VR adjustment driver |
VR adjustment driver, Reflector(MS-2 |
- |
| Common |
BR : Fixing nuts, Washer
BRP : Fixing nuts |
| Approval |
CE |
| Unit weight |
• BRP Series : Approx. 100g
• BR Series : Approx. 120g
• BRP-C Series : Approx. 30g
• BR-C Series : Approx. 50g |
• BR Series:Approx. 300g
• BR-C Series:Approx. 110g |
*1: Non-glossy white paper 50×50mm
*2: Non-glossy white paper 100×100mm *3: The sensing distance is specified with using the MS-2 reflector. Sensing distance is setting range of the reflector. The sensor can detect under 0.1m.
*Tightening torque for connector is 0.39 to 0.49N.m.
*The temperature or humidity mentioned in Environment indicates a non freezing or condensation environment. |