Amprobe Micro-Ohmmeter / Milliohmmeter / Megohmmeter

Typical Applications for Micro-Ohmmeters

Since an increase in contact resistance may lead to power loss and an increase in temperature, many problems in equipment or in the system may occur. The most common uses would be to measure the contact resistance of electrical connections either at the breaker, incoming service or at other bus-bar or high voltage connections. It is suggested to measure contact resistance (bonding) at regular intervals.
 
Here is an example of the difference in power loss in the same circuit with different resistance values. At 10K amps with a contact resistance of 0.1 milli-ohm, the power loss would be 10 KW. If the contact resistance for the same connection was 1 milli-ohm, the power loss becomes 100 KW.

Features to Consider when selecting Micro-ohm Meters

Milli-Ohmmeters, (or Milliohmmeters / Milliohm Meters), are designed to measure low resistance at high accuracy confirming the value and integrity of any electrical circuit and connection. These meters may be used to evaluate component or circuit resistance in PC boardresistance in laboratories and research and design departments, motor winding opens and shorts, transformers, heating elements, contact resistances of switches and connectors or low resistance connections for bonding. Most meters used will utilize a four-wire (terminal) Kelvin System. (See the discussion above for more on Kelvin Probes)

Features to consider when choosing Milliohm Meters

• Resistance Ranges
• Resolution
• Bench-Top 
• Hand-Held Portable
• Digital Display Number of Counts
• Accuracy and Sensitivity
• Test Current
• Go / No-Go Alarms
• Four wire Kelvin Probes
• Manual or Auto-Ranging
• Temperature Compensation
• Interface Capability
• Memory Capability
• Over-temperature and over-voltage protection
• Enclosure IP rating
• Power Supply

Typical Applications for Milliohmmeters

• Printed Circuit Boards
• Capacitors
• Motor Coils
• Transformers
• Generators
• Relay Contacts
• Electrical Connections
• Cable Joints
• Earth Bonding Systems
• Electronics Board Component Resistance
• Electronic Control Components and Relays
• Compression Joints
• Switchboard and Substation Grounding and Wiring

It should be noted that when measuring resistance, there may be changes in final measurements based on the thermal effects of temperature. Please check the manufacturer’s manual for compensation or measurement considerations especially when the product under test contains dissimilar metals.

Megohmmeters/ Insulation Resistance Testers

Megohmmeters, or Insulation Resistance (IR) Testers, are used to measure the resistance, integrity and safety of electrical wiring insulation. As electrical insulation breaks down, there are many hazards that may occur. Electrical shock and injury to personnel, system failure as well as machinery failure, fire hazard and certainly operation downtime become major problems.
 
Insulation Testing is recommended to be included as part of a normal annual or semi-annual maintenance program. If a program is initiated and insulation deterioration and wiring hazards are found, maintenance and repair times can be scheduled. Insulation failure and deterioration is caused by many factors. Some of those include excessive heat or cold, mechanical damage, moisture, dirt, corrosive vapors, vibration, aging and cut or broken wiring.

Typical Applications for Megohmmeters

• Wiring and Cable
• Transformers
• Motors
• Generators
• Switchgear
• Capacitors
• Rotating Machinery
• Insulators
• Acceptance Testing for Conformance
• Preventive Site Maintenance
• QA in Manufacturing
• Diagnostic Testing.
• Multi-Layer Insulation (DD)

3 Primary Insulation Test Methods

There are a variety of accepted test methods for insulation testing. There are primarily three different tests performed when considering Insulation Resistance. These are used for motors, transformers and generators, but may also be used for wire and cable. Please note that all insulation tests should only be performed on de-energized circuits.

1. Spot Reading Test

A Spot Reading test is a single insulation test taken at a fixed voltage over the same time interval and usually done on a regular maintenance program schedule. The time interval for each test is usually no less than 60 seconds. Many spot tests are done annually, but may be done more frequently. All tests must be done with the identical existing conditions, so that temperature and humidity should be as close to the previous test. The timing of these tests is based on individual requirements, but should always be at the identical voltages at approximately the same time of year. These results are plotted to show the “history” of each test product over time. Please see Figure 1 below that indicates a 6 year tabulation of “Spot Reading Tests” where product failure and deterioration is shown over a period of years. Note the correction of the insulation problem indicated in the tabulation.

2. Time Resistance Test

This test applies a selected voltage over two periods of time. The first period is usually at 10 minutes and the second period is at 1 minute. If the equipment insulation is good, the insulation resistance increases over time. If the insulation is damaged or the integrity of the insulation contains moisture, oil or other contaminants, the resistance values will remain level or decrease. Please note figure 2 below which demonstrates that product D is acceptable and product E may be questionable. When proceeding with the Time Test, it is important to note the following:
   
Dielectric Absorption, DAR- (also referred to “absorption ration”), is an indication of good insulation. DAR values that have been used as empirical references, especially for motors and windings are:
 
If the DAR value is less than 1.0, the unit under test has probably failed
If the DAR value is between 1.0 and 1.25, the unit is questionable
If the DAR value is between 1.4 and 1.6, the unit is good
If the DAR value is above 1.6, the unit is excellent

3. Step Voltage

This test incorporates applying two or more test voltages over a fixed interval of time. The increase in Voltage applies an increased stress level on possible insulation leakage paths. This procedure may find problems in insulation that otherwise products may have tested OK with either the Spot or Time Tests. Please note that figure three below demonstrates that a test at 500V has different results from a 2500V test. Many technicians choose 5 different voltages, but each test must be at the identical time interval. The intervals are usually set at 1 minute and range each minute from 1 minute to 10 minutes. Please note that figure 2 above shows a 10 minute test that indicates that product D is fine but Product E is questionable and may contain damage. When applying the Step Voltage Test, a standard interpretation of the results is called the Polarization Index and is represented by:
 
      Polarization Index (PI) = 10 minute test resistance / 1 minute test resistance
 
The Polarization Index is the ratio of the 10-minute insulation resistance test to the 1-minute insulation resistance test. The results will indicate whether any insulation deterioration is occurring. This will be a good test especially for motor windings. The IEEE Standard for minimum values for rotating machinery based on class is:
 
          Class A = 1.5
          Class B = 2.0

Amprobe AMB Series Insulation Resistance Tester