Digital Storage Oscilloscope TDS6000 Series Characteristics Vertical System | | TDS6604B | TDS6804B | TDS6124C | TDS6154C | | Input Channels | 4 | | Bandwidth, Risetime (DSP) | N/A | 8 GHz 50 ps (10–90%) (typical) 35 ps (20–80%) (typical) | 12 GHz 35 ps (10-90%) (typical) 24 ps (20-80%) (typical) | 15 GHz 28 ps (10–90%) (typical) 19 ps (20–80%) (typical) | | True Analog Bandwidth (-3 dB), typical Risetime | 6 GHz 70 ps (10–90%) (typical) 53 ps (20–80%) (typical) | 7 GHz 62 ps (10–90%) (typical) 43 ps (20–80%) (typical) | 12 GHz 35 ps (10–90%) (typical) 24 ps (20–80%) (typical) | 12 GHz 35 ps (10–90%) (typical) 24 ps (20–80%) (typical) | | Hardware Bandwidth Limits(Requires TCA-1 MEG Adapter) | Full, 250 MHz, or 20 MHz | | Input Coupling | DC, GND | | Input Impedance | 50 O ±2.5% | 50 O ±2% | | Input Sensitivity, 50 O | Full-scale 100 mV to 10 V (10 mV/div to 1 V/div).Full-scale is the peak-peak digitizer range at a given sensitivity.Volts/div = Full-scale ÷ 10. | Full-scale 50 mV to 10 V (5 mV/div*1 to 1 V/div).Full-scale is the peak-peak digitizer range at a given sensitivity.Volts/div = Full-scale ÷ 10. | | Vertical Resolution | 8-Bit (>11-Bit with averaging) | | Max Input Voltage, 50 O (Also determined by TekConnect® accessory) | <1 VRMS for <100 mV/div, <7 VRMS for =100 mV/div settings. | <1 VRMS for <1 V full-scale, <5.5 V for =1 V full-scale. | | DC Gain Accuracy | ±(2.5% + (2% × offset)) | ±2% | | Position Range | ±5 divisions | | Offset Range*2 | Fullscale settings: 100 mV to 500 mV: ±0.5 V 505 mV to 995 mV: ±0.25 V 1 V to 5 V: ±5 V 5.05 V to 10 V: ±2.5 V | Fullscale settings: 100 mV: ±0.45 V 200 mV: ±0.4 V 500 mV: ±0.25 V 1 V: ±4.5 V 2 V: ±4.0 V 5 V: ±2.5 V 10 V: 0 General Formula for offset range 100 mV to 995 mV: ±|0.5 V – Fullscale/2| 1 V to 10 V: ±|5 V – Fullscale/2| | | Offset Accuracy | ±(0.7% × offset + 1.5 mV + 0.1 × V/div setting) for ranges <100 mV/div ±(0.8% × offset + 15 mV + 0.1 × V/div setting) for ranges =100 mV/div | ±(0.35% × offset + 1.5 mV + 0.1 × V/div setting) for ranges <100 mV/div ±(0.35% × offset + 15 mV + 0.1 × V/div setting) for ranges =100 mV/div | | Channel-to-channel Isolation for Any Two Channels at Equal Vertical Scale | =80:1 at 1.5 GHz =15:1 at rated bandwidth | =150:1 at 0 to 10 GHz >80:1 at 10 GHz to 12 GHz =50:1 at 12 GHz to 15 GHz | Vertical System (Cont.) | | Full Scale Gain Setting | TDS6000B DSP OFF | TDS6154C DSP ON | TDS6124C DSP ON | BOTH DSP OFF | | Noise, typical | 100 mV | 950 µV | 690 µV | 570 µV | 670 µV | | 160 mV | — | 950 µV | 840 µV | 950 µV | | 200 mV | 1.6 mV | 1.1 mV | 940 µV | 1.0 mV | | 300 mV | — | 1.6 mV | 1.45 mV | 1.6 mV | | 400 mV | — | 2.1 mV | 1.85 mV | 2.1 mV | | 500 mV | 3.55 mV | 2.5 mV | 2.3 mV | 2.4 mV | | 800 mV | — | 4.4 mV | 3.8 mV | 4.1 mV | | 900 mV | — | 4.8 mV | 4.3 mV | 4.6 mV | | 1 V | 9.5 mV | 6.9 mV | 5.7 mV | 6.8 mV | | 2 V | 16 mV | 10.5 mV | 9.5 mV | 10.0 mV | | 5 V | 35.5 mV | 25 mV | 23 mV | 24 mV | | 10 V | 68 mV | 56 mV | 46 mV | 50 mV | *1 5 mV/div is a software zoom with 7 bits digitizer resolution at 50 mV full scale. *2 Offset range in addition to ±5 division position range. Timebase System | | TDS6000B Models | TDS6000C Models | | Timebase Range | 25 ps to 40 s/div; Interpolation down to 500 fs/pt. | | Timebase Delay Time Range | 5 ns to 250 s | | Channel-to-channel Deskew Range | ±75 ns | | Trigger Jitter (RMS) | <1.5 psRMS (typical) | <1 psRMS (typical) | | Long Term Sample Rate and Delay Time Accuracy | <2 ppm over any =100 ms interval | | Clock Stability | <1 ppm (typical) <2.5 ppm (guaranteed) | | Jitter Noise Floor | | 420 fsRMS (typical) over 10 µs duration or less | | Delta Time Accuracy | [(0.06/sample rate) + (2.5 ppm × [Reading])]RMS, typical*3 | 635 fsRMS over <100 ns duration, typical*4 | *3 Test conditions: Sample mode, at 20 GS/s. *4 Test conditions: Sample mode, 500 mV full scale (50 mV/div) setting, input signal 350 mV with rise time (10% to 90%) <50 ps. Acquisition System | | TDS6000B Models | TDS6000C Models | | Max Sample Rate | 20 GS/s on 4 channels | 40 GS/s on 2 channels, 20 GS/s on 4 channels | | Equivalent Time Sample Rate (max) | 2 TS/s | | Maximum Record Length per Channel | 32M (requires option 4M) | 64M on two channels; 32M on all 4 channels (requires option 4M) | | Standard | 2M on all 4 Channels | 4M on two channels; 2M on all 4 Channels | | with Memory Opt. 2M | 8M on all 4 Channels | 16M on two channels; 8M on all 4 Channels | | with Memory Opt. 3M | 16M on all 4 Channels | 32M on two channels; 16M on all 4 Channels | | with Memory Opt. 4M | 32M on all 4 Channels | 64M on two channels; 32M on all 4 Channels | Maximum Time Duration Captured at Highest Real-time Resolution (All Channels) | | TDS6000B Models (All Channels) | TDS6000C Models (Two Channels) | | Max Duration with Standard Memory | 100 µs | 100 µs | | Max Duration with Opt. 2M | 400 µs | 400 µs | | Max Duration with Opt. 3M | 800 µs | 800 µs | | Max Duration with Opt. 4M | 1.6 ms | 1.6 ms | Acquisition Modes | | All Models | | Waveform Database | Accumulate Waveform Database providing three-dimensional array of amplitude, time and counts | | Sample | Acquire sampled values. | | Peak Detect | Captures narrow glitches at all real-time sampling rates | | Minimum Peak Detect Pulse Width | 50 ps | | Averaging | From 2 to 10,000 waveforms included in average | | Envelope | From 2 to 2x109 waveforms included in min-max envelope | | Hi-Res | Real-time boxcar averaging reduces random noise and increases resolution | | FastFrame™ Acquisition | Acquisition memory divided into segments; maximum trigger rate >310,000 waveforms per second. Time of arrival recorded with each event | | Roll Mode | 200 kS/s at 8 Meg Record length and 500 kS/s at 4 Meg Record Length on all channels. | Pinpoint™ Trigger System | | All Models | | Sensitivity | | Internal DC Coupled | 0.5 div DC to 50 MHz increasing to 2.5 div at 7 GHz (TDS6000B models, typical) 0.4 div DC to 50 MHz , increasing to 1 div at 3 GHz, increasing to 3 div at 9 GHz (TDS6000C models, typical) | | External (auxiliary input) | 250 mV DC to 50 MHz, increasing to 350 mV at 1 GHz, increasing to 500 mV at 2 GHz (typical) | | Trigger Characteristics | | Main Trigger Modes | Auto, Normal, and Single. | | A Event & Delayed B Event Trigger Types | Edge, Glitch, Runt, Width, Transition Time, Timeout, Pattern, State, Setup/Hold, Window – all except Edge, Pattern, and State can be Logic State qualified by up to two channels. | | Trigger Sequences | Main, Delayed by Time, Delayed by Events, Reset by Time, Reset by State, Reset by Transition. All sequences can include separate horizontal delay after the trigger event to position the acquisition window in time. | | Communications-related Triggers (requires Option SM) | Support for AMI, HDB3, BnZS, CMI, MLT3 and NRZ encoded communications signals up to 3.125 Gb/s. Select among isolated positive or negative one, zero pulse form or eye patterns as applicable to standard. | | Serial Pattern Trigger (requires Option ST) | 64-Bit serial word recognizer, bits specified in binary (high, low, don't care) or hex format. Trigger on NRZ-encoded data up to 1.25 Gbaud. TDS6000C models only: trigger on 8b/10b encoded data up to 3.125 Gbaud (40 bits). | | Trigger Level Range | | Internal | ±12 divisions from center of screen | | External (auxiliary in) | ±5 V | | Line | Fixed at 0 V | | Trigger Coupling | DC, AC (attenuate <60 Hz), HF reject (attenuate >30 kHz). LF reject (attenuates <80 kHz) Noise reject (reduce sensitivity). | | Trigger Holdoff Range | 250 ns minimum to 12 s maximum. | Trigger Types Edge - Positive and/or negative slope on any channel or front panel auxiliary input. Coupling includes DC, AC, noise reject, HF reject, and LF reject. Glitch - Trigger on or reject glitches of positive, negative, or either polarity. Minimum glitch width is down to 100 ps with re-arm time of 250 ps. Width - Trigger on width of positive or negative pulse (down to 100 ps) either within or out of selectable time limits. Runt - Trigger on a pulse that crosses one threshold but fails to cross a second threshold before crossing the first again. Optional time qualification. Timeout - Trigger on an event which remains high, low, or either, for a specified time period, selectable from 360 ps to 1 s. Transition - Trigger on pulse edge rates that are faster or slower than specified. Slope may be positive, negative, or either. Setup/Hold - Trigger on violations of both setup time and hold time between clock and data present on any two input channels. Pattern - Trigger when pattern goes false or stays true for specified period of time. Pattern (AND, OR, NAND, NOR) specified for four input channels defined as HIGH, LOW, or Don't Care. State - Any logical pattern of channels (1, 2, 3) clocked by edge on channel 4. Trigger on rising or falling clock edge. Window - Trigger on an event that enters or exits a window defined by two user-adjustable thresholds. Event can be time or logic qualified. Trigger Delay by Time - 5 ns to 250 seconds. Trigger Delay by Events - 1 to 10,000,000 Events. Waveform Measurements Amplitude - Amplitude, High, Low, Maximum, Minimum, Peak to Peak, Mean, Cycle Mean, RMS, Cycle RMS, Positive Overshoot, Negative Overshoot. Time - Rise time, Fall time, Positive Width, Negative Width, Positive Duty Cycle, Negative Duty Cycle, Period, Frequency, Delay. Combination - Area, Cycle Area, Phase, Burst Width. Histogram-related - Waveform count, Hits in box, Peak hits, Median, Maximum, Minimum, Peak-to-peak, Mean (µ), Standard Deviation (s), µ + 1s, µ + 2s, µ + 3s. Eye Pattern-related - Extinction Ratio (absolute, %, and dB), Eye Height, Eye Top, Eye Base, Eye Width, Crossing %, Jitter (peak-peak, RMS and 6sigma), Noise (peak-peak and RMS), S/N ratio, Cycle Distortion, Q-factor. Waveform Processing/Math Algebraic Expressions - Define extensive algebraic expressions including waveforms, scalars and results of parametric measurements e.g. (Integral (CH.1-Mean(CH.1))×1.414). Arithmetic - Add, subtract, multiply, divide waveforms and scalars. Relational - Boolean result of comparison >, <, =, =, =, ?. Calculus - Integrate, differentiate. Frequency Domain Functions - Spectral magnitude and phase, real and imaginary spectra. Vertical Units - Magnitude: Linear, dB, dBm; Phase: Degrees, radians. Window Functions - Rectangular, Hamming, Hanning, Kaiser-Bessel, Blackman-Harris, Gaussian, Flattop2, Tek Exponential. Waveform Definition - As arbitrary math expressions. Display Characteristics Display Type - Liquid crystal active-matrix color display. Display Size - Diagonal: 264 mm (10.4 in.). Display Resolution - 1024 horizontal x 768 vertical pixels. Waveform Styles - Vectors, Dots, Variable Persistence, Infinite Persistence. Computer System and Peripherals CPU - Intel Pentium 4 processor, 2.8 GHz. PC System RAM - 1 GB (266 MHz DDR). Hard Disk Drive - 40 GB removable hard disk drive: rear-panel standard or front-panel (option FHD). USB Ports - One front panel, four on rear panel, USB2.0 compliant. CD-R/W Drive - Front-panel CD-R/W standard or rear-panel (option FHD). Mouse - Optical scroll wheel model included, USB interface. Keyboard - Small keyboard included (fits in pouch). Order 119–6297–xx for full-size keyboard; USB interface and hub. Input/Output Ports Front Panel Fast Edge Output - Front panel SMA connector provides fast edge signal. TDS6000B models: Amplitude 350 mV ±20% into a =50 O load, frequency 1 kHz ±5%, 200 ps typical risetime. TDS6000C models: Amplitude 440 mV pk-pk, ±20% in a 50 O load; VOH +0.3 V, VOL – 0.14 V; frequency 1 kHz ±5%, 200 ps typical rise time. Recovered Clock - SMA connector, =1.25 Gb/s, Output swing =130 mV pk-pk into 50 O. Requires Opt. SM or Opt. ST to enable. Recovered Data - SMA connector, =1.25 Gb/s, Output swing of 1010 repeating pattern 200 mV into 50 O. Requires Opt. SM or Opt. ST to enable. DC Probe Calibration Output - BNC connector, ±10 V DC for DC probe calibration. (Signal available only during probe calibration.) AUX Trigger Output - BNC connector, provides a TTL-compatible, polarity switchable pulse when the oscilloscope triggers. USB2.0 Port - One in front. Allows connection or disconnection of USB keyboard, mouse, or storage device while oscilloscope is on. Rear Panel External Time Base Reference In - BNC connector; allows time base system to phase-lock to external 10 MHz reference. Time Base Reference Out - BNC connector; provides TTL-compatible output of internal 10 MHz reference oscillator. Aux Trigger Input - BNC, see Ext Trigger specification. Parallel Port - IEEE 1284, DB-25 connector. Audio Ports - Miniature phone jacks for stereo microphone input and stereo line output. USB2.0 Ports - Four in back. Allows connection or disconnection of USB keyboard, mouse, or storage device while oscilloscope power is on. Keyboard Port - PS-2 compatible. Mouse Port - PS-2 compatible. LAN Port - RJ-45 connector, supports 10BaseT, 100BaseT, and 1000BaseT. Serial Port - DB-9 COM1 port. Windows Video Port - 15 pin D-Sub connector on the rear panel; connect a second monitor to use dual-monitor display mode allowing analysis results and plots to be viewed along with the oscilloscope display. Video is DDC2B compliant. GPIB Port - IEEE 488.2 standard. Scope XGA Video Port - 15 pin D-Sub connector on the rear panel, video is IBM XGA compatible. Connect to show the oscilloscope display, including live waveforms on an external monitor or projector. The primary Windows desktop can also be displayed on an external monitor using this port. Power Source Power - 100 to 240 VRMS, ±10%, 50/60 Hz; 115 VRMS ±10%, 400 Hz; CAT II, <500 W typical (650 VA). Option SM 156 Standards Masks Supported - ITU-T (1.544 Mb/s - 155 Mb/s) ANSI T1.102 (1.544 Mb/s - 155 Mb/s) Ethernet IEEE Std 802.3, ANSI X3.263 (1.544 Mb/s - 3.125 Gb/s XAUI) Sonet/SDH (51.84 Mb/s - 2.4883 Gb/s) Fibre Channel (133 Mb/s - 4.25 Gb/s*3) InfiniBand (2.5 Gb/s) USB (12 Mb/s - 480 Mb/s) Serial ATA (1.5 Gb/s, 3.0 Gb/s) Serial Attached SCSI (1.5 Gb/s, 3.0 Gb/s) IEEE 1394b (491.5 Mb/s - 1.966 Gb/s) RapidI/O (1.25 Gb/s - 3.125 Gb/s) OIF Standards (2.488 Gb/s - 3.11 Gb/s) PCI Express (2.5 Gb/s) *3 4.25 Gb/s mask supported using Glitch Trigger. Physical Characteristics | BENCHTOP CONFIGURATION | | Dimensions | mm | in. | | Height | 282 | 11.1 | | Width | 457 | 18.0 | | Depth | 540 | 23.25 | | Weight | kg | lb. | | Net | 21 | 47 | | Shipping | 32.3 | 71.2 | | RACKMOUNT CONFIGURATION | | Dimensions | mm | in. | | Height | 267 | 10.5 | | Width | 491 | 19.3 | | Depth | 638 | 25.1 | | Weight | kg | lb. | | Net | 22 | 49 | | Kit | 5.6 | 12.25 | Mechanical | Cooling - Required Clearance | mm | in. | | Top | 0 or >76 | 0 or >3 | | Bottom | 25 | 1 | | Left side | 76 | 3 | | Right side | 76 | 3 | | Front | 0 | 0 | | Rear | 0 | 0 | Environmental Temperature Operating - Excluding CD-R/W drive: TDS6000B models: +5 °C to +40 °C. TDS6000C models: +10 ºC to +45 ºC. Including CD-R/W drive: +10 °C to +40 °C. Nonoperating - –22 °C to +60 °C. Humidity Operating - 20% to 80% relative humidity with a maximum wet bulb temperature of +29 °C at or below +50 °C, noncondensing. Upper limit derated to 25% relative humidity at +50 °C. Nonoperating - 5% to 90% relative humidity with a maximum wet bulb temperature of +29 °C at or below +60 °C, noncondensing. Upper limit derated to 20% relative humidity at +60 °C. Altitude Operating - 10,000 ft. (3,048 m). Nonoperating - 40,000 ft. (12,190 m). Random Vibration Operating - 0.000125 g2/Hz from 5 to 350 Hz, -3 dB/octave from 350 to 500 Hz, 0.0000876 g2/Hz at 500 Hz. Overall level of 0.24 gRMS. Nonoperating - 0.0175 g2/Hz from 5 to 100 Hz, -3 dB/octave from 100 to 200 Hz, 0.00875 g2/Hz from 200 to 350 Hz, -3 dB/octave from 350 to 500 Hz, 0.006132 g2/Hz at 500 Hz. Overall level of 2.28 gRMS. Certifications Electromagnetic Compatibility - 89/336/EEC. Safety - UL 3111-1, CSA1010.1, EN61010-1, IEC 61010-1. |