| I²S/LJ/RJ/TDM Characteristics |
| Word size |
4-32 bits |
| Clock |
Rising or falling edge |
| Word Select polarity |
Normal or inverted |
| Data High |
1 or 0 |
| Bit order |
Most Significant (MS) First Least Significant (LS) First |
| Bus |
Bus only |
| Bus and waveforms |
Simultaneous display of bus and logic waveforms |
| Event Table |
Decoded packet data in a tabular view |
| Trigger and/or Search On |
Word Select Frame Sync
Data (select either word, left word, or right word; trigger or search when =, ≠,<,>, ≤, ≥, inside range, outside range) |
| Maximum Clock/Data Rate |
Up to 12.5 Mb/s (for automated decoding of I2S/LJ/RJ bus) Up to 25 Mb/s (for automated decoding of TDM bus) |
| Decode display |
Start (green bracket) Data (cyan box)
Stop (red bracket |
| I²C Characteristics |
| Bus |
Bus only |
| Bus and waveforms |
Simultaneous display of bus and logic waveforms |
| Event table |
Decoded packet data in a tabular view |
| Trigger and/or Search On |
Start
Stop
Repeated Start Missing Ack
Address (7 or 10 bit) with R/W Selection
Data (number of bytes 1-5)
Address and Data |
| Maximum Clock/Data Rate |
Up to 10 Mb/s (for automated decoding of bus) |
| Decode Display |
Start (green bracket)
Address (yellow box)
Missing Ack (red ! symbol)
Data (cyan box)
Stop (red bracket) |
| SPI Characteristics |
| Sources (Clock, Slave Select, MOSI, and MISO) |
Analog channels 1-4 Digital channels D0-D15 |
| Thresholds |
Per-channel thresholds |
| Recommended probing |
Single ended |
| Decode configuration |
- |
| Framing |
Idle Time (2-wire SPI) Slave Select (3-wire or 4-wire SPI) |
| Clock |
Rising or Falling Edge |
| Slave select |
Active High or Active Low |
| MOSI |
Active High or Active Low |
| MISO |
Active High or Active Low |
| Word size |
4-32 bits |
| Bit order |
Most Significant (MS) First Least Significant (LS) First |
| Decode formats available |
Hex, Binary |
| Display modes |
- |
| Bus |
Bus only |
| Bus and waveforms |
Simultaneous display of bus and logic waveforms |
| Event table |
Decoded packet data in a tabular view |
| Trigger and/or Search On |
SS Active Start of Frame
MOSI
MISO
MOSI and MISO
Data: maximum of 128 bits (up to four 32-bit words or 32 four-bit words) |
| Maximum Clock/Data Rate |
Up to 50 Mb/s (for automated decoding of bus) |
| Decode display |
Start (green bracket) Data (cyan box)Stop (red bracket) |
| RS-232/UART/RS-422/RS-485 Characteristics |
| Pre-defined list of rates |
50 b/s - 2.8 Mb/s |
| Custom |
50 b/s - 10 Mb/s |
| Data bits |
7, 8, or 9 |
| Parity |
None, Odd, or Even |
| Packets |
On or Off |
| End of packet |
00h (NUL)
0Ah (LF)
0Dh (CR)
20h (SP)
FFh |
| Bus |
Bus only |
| Bus and waveforms |
Simultaneous display of bus and logic waveforms |
| Event table |
Decoded packet data in a tabular view |
| Trigger and/or Search On |
Tx Start Bit Rx Start Bit
Tx End of Packet
Rx End of Packet
Tx Data (number of bytes 1-10)
Rx Data (number of bytes 1-10)
Tx Parity Error
Rx Parity Error |
| Maximum Clock/Data Rate |
Up to 10 Mb/s (for automated decoding of bus) |
| Decode display |
Data (cyan box) Errors (red box)
- Parity
- Framing |
| CAN, CAN FD (ISO and non-ISO) Characteristics |
| Standard: pre-defined list of rates and Custom |
10 Kb/s - 1 Mb/s |
| FD: Pre-defined and custom |
1 Mb/s - 10 Mb/s (7 M/bs MDO3K) |
| Bus |
Bus only |
| Bus and waveforms |
Simultaneous display of bus and logic waveforms |
| Event table |
Decoded packet data in a tabular view |
| Trigger and/or Search On |
Start of Frame Type of Frame (Data, Remote, Error, Overload)
Identifier (Standard or Extended)
Data (number of bytes 1-8, trigger or search when =, ≠, <, >, ≤, ≥)
Identifier and Data
End of Frame
Missing Ack
Bit Stuffing Error
FD BRS Bit
FD ESI Bit
Form Error
Any Error |
| Decode display |
Start (green bracket)
Address (yellow box)
DLC, CRC (purple box)
Missing Ack (red ! symbol)
Data (cyan box)
Stop (red bracket) Bit stuffing errors (red box) |