| General Specifications |
| Frequency range |
1 µHz to 150 MHz |
| Sine wave in Burst Mode |
1 µHz to 75 MHz |
| Effective maximum frequency out |
150 MHz |
| Amplitude flatness (1 Vp-p) |
<5 MHz: ±0.15 dB
≥5 MHz to <25 MHz: ±0.3 dB
≥25 MHz to ≤150 MHz: ±0.5 dB |
| Amplitude flatness (1 Vp-p), typical |
>5 MHz: ±0.04 dB
≥5 MHz to 50 MHz: ±0.02 dB
≥50 MHz to 150 MHz: ±0.03 dB |
| Harmonic distortion (1 Vp-p) |
10 Hz to 1 MHz: < -60 dBc
≥1 MHz to <5 MHz: < -50 dBc
≥5 MHz to ≤150 MHz: < -37 dBc |
| Harmonic distortion (1 Vp-p), typical |
10 Hz to 1 MHz: < -72 dBc
≥1 MHz to 5 MHz: < -66 dBc
≥5 MHz to 100 MHz: < -42 dBc
≥100 MHz to 150 MHz: < -48 dBc |
| THD |
≤0.2% (<0.15%, typical), 10 Hz to 20 kHz, 1 Vp-p |
| Spurious(1 Vp-p) |
10 Hz to 1 MHz: < -60 dBc
≥1 MHz to 25 MHz: < -50 dBc
≥25 MHz to 150 MHz: - 50 dBc + 6 dBc/octave |
| Spurious(1 Vp-p), typical |
10 Hz to 1 MHz: < -70 dBc
≥1 MHz to 25 MHz: < -54 dBc
≥25 MHz to 50 MHz: < -66 dBc
≥50 MHz to 100 MHz: < - 68 dBc
≥100 MHz to 150 MHz: < - 38 dBc |
| Phase noise, typical |
< -110 dBc/Hz at 20 MHz, 10 kHz offset, 1 Vp-p |
| Residual clock noise |
-57 dBm |
| Frequency range |
1 µHz to 100 MHz |
| Rise/fall time |
≤3.5 ns |
| Jitter (RMS) |
150 ps |
| Jitter (RMS), typical |
<35 ps |
| Frequency range |
1 µHz to 1.5 MHz |
| Linearity, typical |
≤0.15% of peak output |
| Symmetry |
0% to 100.0% |
| Frequency range |
1 mHz to 100 MHz |
| Pulse width |
5.00 ns to 999.99 s |
| Resolution |
10 ps or 5 digits |
| Pulse duty |
0.001% to 99.999% (Limitations of pulse width apply) |
| Edge transition time |
3 ns to 625 s |
| Resolution |
10 ps or 4 digits |
| Lead delay: range |
(Continuous Mode): 0 ps to Period
(Triggered/Gated Burst Mode): 0 ps to Period - [Pulse Width + 0.8 * (Leading Edge Time + Trailing Edge Time)] |
| Lead delay: resolution |
10 ps or 8 digits |
| Overshoot, typical |
<5% |
| Jitter (RMS) |
150 ps |
| Jitter (RMS), typical |
<25 ps |
| Frequency range |
1 µHz to 1.5 MHz |
| Noise bandwidth (-3 dB) |
180 MHz |
| Noise type: |
White Gaussian |
| Internal noise add |
When activated, output signal amplitude is reduced to 50% |
| Level |
0.0% to 50% of amplitude (Vp-p) setting |
| Resolution |
1% |
| DC (into 50 Ω) |
-5 V to +5 V |
| Frequency range |
1 mHz to 100 MHz |
| Arbitrary waveforms in Burst Mode |
1 mHz to 50 MHz |
| Effective analog bandwidth (-3 dB) |
180 MHz |
| Nonvolatile memory |
4 waveforms |
| Memory: Sample rate (1K=1024 points) |
2 to 16 K: 1 GS/s
>16 K to 128 K: 250 MS/s |
| Vertical resolution |
14 bits |
| Rise/fall time |
5 ns |
| Jitter (RMS) |
750 ps at 1 GS/s 4 ns at 250 MS/s |
| Range, 50 Ω Load |
≤100 MHz: 20 mVp-p to 10 Vp-p >100
MHz: 20 mVp-p to 8 Vp-p |
| Range (open circuit or High Z) |
≤100 MHz: 40 mVp-p to 20 Vp-p>100 MHz: 40 mVp-p to 16 Vp-p |
| Accuracy |
±(1% of setting +1 mV) (1 kHz sine wave, 0 V offset, >10 mVp-p amplitude) |
| Accuracy, typical |
±(0.5% of setting +0.5 mV) (1 kHz sine wave, 0 V offset, >10 mVp-p amplitude) |
| Resolution |
0.1 mVp-p, 0.1 mVRMS, 1 mV, 0.1 dBm or 4 digits |
| Units |
Vp-p, VRMS, dBm (sine wave only) and Volt (high/low setting) |
| Output impedance |
50 Ω |
| Load impedance setting |
Selectable: 50 Ω, 1 Ω to 10.0 kΩ, High Z (Adjusts displayed amplitude according to selected load impedance) |
| Isolation |
42 Vpk maximum to earth |
| Short-circuit protection |
Signal outputs are robust against permanent shorts against floating ground |
| External voltage protection |
To protect signal outputs against external voltages use fuse adapter 013-0345-xx |
| Range (50 Ω load) |
±5 Vpk DC |
| Range (open circuit or High Z) |
±10 Vpk DC |
| Accuracy |
±(1% of |setting| + 5 mV + 0.5% of amplitude (Vp-p )) |
| Resolution |
1 mV |