Standard Waveforms |
Range Frequency |
Sine: |
1µHz to 500MHz |
Square, Pulse: |
1µHz to 350MHz |
All Others: |
1µHz to 125MHz |
SINE |
Start Phase: |
0-360° |
Phase Resolution |
0.01° |
Harmonics Distortion @1Vp-p (Typ.): |
5MHz to 200MHz: |
<-40dBc |
200MHz to 350MHz: |
<-50dBc |
Non-Harmonics Distortion @1Vp-p (Typ.): |
1MHz to 100MHz: |
<-80dBc |
100MHz to 250MHz: |
<-75dBc |
250MHz to 350MHz: |
<-70dBc |
THD: |
0.1% (DC to 100kHz) |
Flatness: |
±0.5dB cross range |
SSB Phase Noise (10kHz offset) typ.: |
1MHz Carrier: |
<-120dBc/Hz |
10MHz Carrier: |
<-118dBc/Hz |
100MHz Carrier: |
<-115dBc/Hz |
250MHz Carrier: |
<-110dBc/Hz |
350MHz Carrier: |
<-100dBc/Hz |
TRIANGLE / RAMP (SAW-TOOTH) |
Start Phase: |
0-360° |
Phase Resolution: |
0.01° |
Timing Ranges: |
1.0%-99.9% of period |
SQUARE |
Duty Cycle Range: |
1.0% to 99.9% |
Resolution: |
0.1% |
Rise/Fall Time: |
<1ns |
Overshoot (typ.): |
<5% (typ) |
Jitter (rms): |
<10ps |
GAUSSIAN |
Time Constant: |
10-200 |
EXPONENTIAL PULSE |
Type: |
Rise or Decay, selectable |
Time Constant: |
-100 to 100 |
REPETITIVE NOISE |
Bandwidth: |
125MHz |
DC |
Range: |
|
WS8101/2: |
-8V to 8V |
WS8104: |
-5V to 5V |
PULSE |
Pulse Mode: |
Single or double, programmable |
Polarity: |
Normal, inverted or complement |
Period: |
4ns to 1.6s |
Parameters Ratio: |
16,000,000 to 1 |
Resolution: |
1ns |
Pulse Width: |
2ns to 1.6s |
Resolution: |
5ns |
Accuracy: |
<2% (typ.) |
Rise/Fall Time: |
|
Fast: |
<1ns |
Linear: |
1ns to 1.6s |
Double Pulse Delay: |
4ns to 1000s |
Impedance: |
50Ω |
Amplitude Window: |
100mVp-p to 4Vp-p (1) |
Low Level: |
-2V to +1.95V (1) |
High Level: |
-1.95V to +2V (1 |
(1) Double into option impedance |
PULSE / PATTERN COMPOSER |
Number of Levels: |
1 to 1000 |
Dwell Time: |
500ps to 10s |
Transition type: |
Fast or Linear |
Memory: |
100k |
Amp. Resolution: |
4 points |
Time Resolution: |
1 to 1k |
Waveform Granularity: |
500ps to 100ns (auto or user |
PATTERN |
Pattern Source: |
PRBS or user-defined |
PRBS Type: |
PRBS7, PRBS9, PRBS11, PRBS15, PRBS23, PRBS31, USER |
Data Rate: |
10Bit/s to 350MBit/s |
Number of Levels: |
2, 3, 4, 5 |
High/Low Levels: |
±2.5V |
Resolution: |
4 digits |
Loops: |
1 to 1e6 |
Preamble: |
1 to 512e3 |
Length: |
1 to 512e3 |
ARBITRARY WAVEFORMS |
Sample Rate: |
10MS/s to 2GS/s |
Vertical Resolution: |
14 bits |
Waveform Memory: |
16Mpts |
Min. Segment Size: |
192 points |
Resolution: |
16 points |
No. of Segments: |
1 to 1k |
Waveform Granularity: |
1 point |
SEQUENCED WAVEFORMS |
Sequencer Steps: |
1 to 1k |
Segment Loops: |
1 to 1M |
Advanced Modes: |
Continuous, once (x“N”), stepped |
Advance Source: |
External, internal or software |
MODULATION |
Carrier Waveform: |
Sine wave |
Carrier Frequency: |
1µHz to 350MHz |
Source: |
Internal |
FM |
Modulating Shape: |
Sine, square, triangle, ramp |
Modulating Freq.: |
100Hz to 35MHz |
Deviation Range: |
10mHz to 175MHz |
FSK / FREQUENCY HOPPING |
FSK Baud Rate: |
10mbps to 350Mbps |
Hop Table Size: |
2 to 256 |
Hop Type: |
Fast or Linear |
Dwell Time Mode: |
Fixed or programmable per step |
Dwell Time: |
2ns to 10s |
Resolution: |
2ns |
SWEEP |
Sweep Step: |
Linear or log |
Sweep Direction: |
Up or Down |
Sweep Time: |
1µs to 10ms |
CHIRP |
Modulation Shape: |
Pulse |
Pulse Repetition: |
|
Range: |
200ns to 20s |
Resolution: |
3 digits |
Accuracy: |
100ppm |
AM |
Envelope Waveform: |
Sine, square, triangle, ramp |
Envelope Freq.: |
100Hz to 1MHz |
Modulation Depth: |
0.1% to 200% |
ASK / AMPLITUDE HOPPING |
ASK Baud Rate: |
10mbps to 350Mbps |
Hop Table Size: |
2 to 256 |
Hop Type: |
Fast or Linear |
Dwell Time Mode: |
Fixed or programmable per step |
Dwell Time: |
2ns to 10s |
Resolution: |
2ns |
COMMON CHARACTERISTICS |
FREQUENCY |
Resolution: |
8 digits |
Accuracy/Stability: |
Same as reference |
ACCURACY REFERENCE CLOCK |
Internal: |
1ppm/year aging rate |
External (10MHz): |
-5dBm to 5dBm, 50Ω |
AMPLITUDE |
Range: |
|
Single-ended: |
50mV to 4Vp-p into 50Ω (1) |
Differential: |
100mV to 8Vp-p into 50Ω (1) |
Resolution: |
4 digits |
Accuracy (1kHz): |
±(3% +5mV) |
Rise/Fall Time: |
<1ns, typ |
Overshoot: |
5%, typ. |
OFFSET |
Range: |
-1.5V to + 1.5V into 50Ω |
Resolution: |
4 digits |
Accuracy: |
±(5% +5mV) |
OUTPUTS |
MAIN OUTPUTS |
Connectors: |
Front panel SMA |
Type: |
Single-ended or differential |
Impedance: |
50Ω ±1% |
Protection: |
Short Circuit to Ground, 10s max |
SYNC OUTPUT |
Connector: |
Front panel SMA |
Source: |
Channel 1 or channel 2 |
Type: |
Single ended |
Waveform Type: |
|
Pulse: |
16 points width |
WCOM: |
Waveform complete |
Impedance: |
50Ω |
Amplitude: |
1V; doubles into high Z |
Variable Position Control: |
Range: |
0 to segment length |
Resolution: |
16 points |
Rise/Fall Time: |
2ns, typ. |
Variable Width Control: |
Range: |
16 points to segment length |
Resolution: |
16 points to segment length |
MARKER OUTPUTS |
Number of Markers: |
4, Differentials |
Connectors: |
Rear panel SMB |
Amplitude Voltage: |
|
Window: |
0V to 1.25V, single-ended; 0V to 2.5V, differential |
Low Level: |
0V to 0.8V, single-ended; 0V to 1.6V, differential |
Low Level: |
0.5 V to 1.25V, single-ended; 0V to 2.5V, differential |
Resolution: |
10mV |
Accuracy: |
10% of setting |
Width Control: |
2 SCLK to segment length |
Position Control: |
|
Range: |
0 to segment length |
Resolution: |
2 points |
Resolution: |
4 digits |
Initial Delay: |
4ns±½ clock (Output to marker |
Variable Delay: |
|
Control: |
0 to segment length |
Range: |
2 points |
Resolution: |
0 to segment length |
Accuracy: |
2 points |
Skew Between Mrk: |
10ps, typ. |
Rise/Fall Time: |
<1ns, typ. |
INPUTS |
TRIGGER & EVENT INPUTS |
Connector: |
|
Trigger In: |
Front panel SMA |
Event In: |
Rear panel BNC |
Frequency Range: |
0 to 15MHz |
Input Impedance: |
10kΩ |
Polarity: |
Positive or negative, selectable |
Damage Level: |
±20V |
Sensitivity: |
100mV |
Trigger Level Control: |
|
Range |
-5V to 5V |
Resolution |
12 bit (2.5mV) |
Accuracy |
±(5% of setting + 2.5mV) |
Sensitivity |
0.2Vp-p |
Min. Pulse Width: |
10ns |
EXTERNAL REFERENCE INPUT |
Connector: |
Rear panel SMB |
Input Frequency: |
10MHz / 100MHz |
Impedance: |
50Ω |
Voltage Swing: |
-5dBm to 5dBm |
Damage Level: |
10dBm |
EXTERNAL SAMPLE CLOCK INPUT |
Connector: |
Rear panel SMA |
Voltage Swing: |
0dBm to 10dBm |
Input Impedance: |
50Ω |
Input Frequency: |
1GHz to 4GHz (Double the internal clock |
Clock Divider: |
1/1, 1/2, 1/4, 1/256, separate for each channel |
Damage Level: |
15dBm |
RUN MODES |
Type: |
Continuous, self armed, armed, triggered, normal, override, gated, burst |
Continuous: |
A selected output function shape is output continuously. |
Self Armed: |
No start commands are required to generate waveforms. |
Armed: |
The output dwells on a DC level and waits for an enable command and then the output waveform is output continuously; An abort command turns off the waveform. |
Triggered: |
A trigger signal activates a single-shot or counted burst of output waveforms and then the instrument waits for the next trigger signal. |
Normal Mode: |
The first trigger signal activates the output; consecutive triggers are ignored for the duration of the output waveform. |
Override Mode: |
The first trigger signal activates the output; consecutive triggers restart the output waveform regardless if the current waveform has been completed or not. |
Gated: |
A waveform is output when a gate signal is asserted. The waveform is repeated until the gate signal is de-asserted. Last period is always completed. |
Burst: |
Upon trigger, outputs a Dual or multiple preprogrammed number of waveform cycles from 1 through 1M. |
TRIGGER CHARACTERISTICS |
EXTERNAL |
Source: |
Channel 1, channel 2, or both |
Slope: |
Positive/Negative, selectable |
Damage Level: |
±20V |
Input Frequency: |
DC to 15MHz |
Trigger Level Control: |
Range: |
-5V to 5V |
Resolution: |
12 bit (2.5mV) |
Accuracy: |
±(5% of setting + 2.5mV) |
Sensitivity: |
0.2Vp-p |
Min. Pulse Width: |
10ns, min |
System Delay: |
200 SCLK periods + 50ns |
Trigger Jitter: |
Separate for each channe |
Range: |
0 to 8M SCLK periods |
Resolution: |
4 points |
Accuracy: |
Same as SCLK accuracy |
Smart Trigger: |
Detects a unique pulse width |
Conditioned Trigger: |
< pulse width, > pulse width or <>pulse width |
PW Range: |
50ns to 2s |
Resolution: |
2ns |
Accuracy: |
±(5% of setting +20ns) |
Trigger Jitter: |
Ignores triggers for a hold-off |
Hold-off Range: |
100ns to 2s |
Resolution: |
2ns |
Accuracy: |
±(5% of setting +20ns) |
Trigger Jitter: |
2ns at max. SCLK (4 SCLK) |
INTERNAL / TIMER |
Range: |
200ns to 20s |
Resolution: |
20ns |
Error: |
3 SCLK + 20ns |
MANUAL |
Source: |
Soft trigger command from the front panel or remote |
INTER-CHANNEL SKEW CONTROL |
Initial skew: |
200ps |
COURSE TUNING |
Control: |
|
Range |
0 to waveform-length points |
Resolution |
4 points |
Accuracy: |
Same as SCLK accuracy |
FINE TUNING |
Control: |
|
Range |
-3ns to +3ns |
Resolution |
10ps |
Accuracy: |
(10% of setting + 20ps) |
GENERAL |
Voltage: |
100 to 240VAC, 50-60Hz |
Power Consumption: |
150W max. |
Display Type: |
TFT, Color LCD |
Size: |
4" |
Resolution: |
320 x 240 pixels |
Interfaces: |
|
USB 2.0: |
|
Host: |
1 x Front, USB type A |
Device: |
1 x Rear, USB type B |
LAN: |
1 x Rear, 1000/100 BASE-T |
GPIB: |
1 x Rear, IEEE-488.2 |
Dimensions (WxHxD): |
|
With Feet: |
315 x 102 x 395 mm |
Without Feet: |
315 x 88 x 395 mm |
Weight: |
|
Without Package: |
4.5 Kg |
Shipping Weight: |
6 Kg |
Temperature: |
|
Operating: |
0°C to +40°C |
Storage: |
-40°C to +70°C |
Warm up time: |
30 minutes |
Humidity: |
85% , non-condensing |
Safety: |
CE Marked, IEC61010-1-1:2008 |
EMC: |
IEC 61326-1:2006 |
Calibration: |
2 years |
Warranty: |
1 year |