| Model |
SDS1102X |
SDS1102X-S |
SDS1202X |
SDS1202X-S |
| Bandwidth |
100MHz |
200MHz |
| Sample Rate(Max) |
1GSa/s |
| Channels |
2+EXT |
| Memory Depth(Max) |
7Mpts/CH (Dual-Channel); 14Mpts/CH (Single-Channel) |
| Waveform Capture Rate |
60,000 wfms/s |
| Trigger Type |
Edge, Slope, Pulse width, Window, Runt, Interval, Dropout, Pattern, Video |
Serial Trigger
(Optional) |
I 2 C, SPI, UART/RS232 |
|
Decode Type
(Optional)
|
I 2 C, SPI, UART/RS232 |
| DDS Waveform Generator |
No |
Yes |
No |
Yes |
| I 2 C, SPI, UART/RS232 |
| I/O |
USB Host, USB Device, LAN, Pass/Fail, Trigger Out, 1KHz Cal |
| Probe(Std) |
2 pcs passive probe PP510 |
2 pcs passive probe PP215 |
| Display |
8 inch TFT LCD (800x480) |
| Weight |
Net weight 3.26 Kg, Gross weight 4.25Kg |
| Sample Rate |
1GSa/s (Single-Channel), 500MSa/s(Dual-Channel) |
| Memory Depth |
Max 14Mpts/Ch (Single-Channel), 7Mpts/Ch (Dual-
Channel) |
| Peak Detect |
1ns |
| Average |
Averages: 4,16, 32,64,128,256,512,1024 |
| Eres |
Enhance bits: 0.5, 1, 1.5, 2, 2.5, 3 Selectable |
Waveform
interpolation |
Sinx/x, Linear |
| Channel |
2 |
| Coupling |
DC, AC, GND |
| Impedance |
DC: (1MΩ±2%) || (18pF ±2pF)
AC: (1.2MΩ±2%) || (18pF ±2pF)
50Ω: 50Ω±2% |
| Max Input voltage |
1MΩ ≤400Vpk(DC + Peak AC <=10kHz),
50Ω ≤5Vrms |
| CH to CH Isolation |
DC~Max BW >40dB |
| Probe attenuator |
0.1X, 0.2X, 0.5X, 1X, 2X, 5X, 10X, 20X, 50X, 100X,
200X, 500X , 1000X |
| Bandwidth (-3dB) |
200MHz (SDS1202X)
100MHz (SDS1102X) |
| Vertical Resolution |
8 bit |
| Vertical Scale (Probe 1X) |
500μV/div - 10V/div (1-2-5 ) |
| Offset Range (Probe 1X) |
500μV ~ 150mV: ± 1V
152mV ~ 1.5V: ± 10V
1.52V ~ 10V: ± 100V |
| Bandwidth Limit |
20MHz ±40% |
| Bandwidth Flatness |
DC ~ 10%(BW): ± 1dB
10% ~ 50%(BW): ± 2dB
50% ~ 100%(BW): + 2dB/-3dB |
Low Frequency Response
(AC-3dB |
≤10Hz (at input BNC) |
| Noise |
ST-DEV ≤0.7 division (<1mV/div)
ST-DEV ≤0.4 division (<2mV/div)
ST-DEV ≤0.2 division (≥2mV/div) |
| SFDR including harmonics |
≥35dB; |
| DC Gain Accuracy |
≤±3.0%: 5mV/div ~10V/div
≤±4.0%: ≤2mV/div |
| Offset Accuracy |
±(1%* Offset+1.5%*8*div+2mV): ≥2mV/div
±(1%* Offset+1.5%*8*div+500uV): ≤1mv/div |
| Rise time |
<1.8ns (SDS1202X)
<3.5ns (SDS1102X) |
| Overshoot(500ps Pulse) |
<10% |
| Time base Scale |
2.0ns/div ~ 50s/div |
| Channel Skew |
<100ps |
| Waveform Capture Rate |
60,000 wfm/s |
| Intensity grading |
256 Levels |
| Display Format |
Y-T, X-Y, Roll |
| Time base Accuracy |
±25ppm |
| Roll Mode |
50ms/div ~ 50s/div (1-2-5 step) |
| Trigger Mode |
Auto, Normal, Single |
| Trigger Level |
Internal: ±4.5 div from the center of the screen
EXT: ±0.6 V
EXT/5: ±3V |
| Hold-off Range |
80ns ~ 1.5s |
| Trigger Coupling |
AC , DC, LFRJ, HFRJ , Noise RJ (CH1~CH2) |
Coupling Frequency Response
(CH1~CH2) |
AC: Blocks DC components and attenuates signals below 5.8Hz
LFRJ: Blocks the DC component and attenuates the low-frequency components below 2 MHz
HFRJ: Attenuates the high-frequency components above 1.2MHz |
Trigger
Accuracy(Typical) |
Internal: ±0.2div
EXT: ±0.4div |
| Trigger Sensitivity |
CH1~CH2: DC~ Max BW 0.6div
EXT: 200mVpp DC ~ 10MHz
300mVpp 10MHz ~ BW frequency
EXT/5: 1Vpp DC ~ 10MHz
1.5Vpp 10MHz ~ BW frequency |
| Trigger Jitter |
<100ps(CH1~CH2) |
| Trigger Displacement |
Pre-Trigger: 0~100% Memory
Delay Trigger: 0 to 10,000 div |
| Slope |
Rising, Falling |
| Limit Range |
<, >, <>, >< |
| Source |
CH1/CH2 |
| Time Range |
2ns ~ 4.2s |
| Resolution |
1ns |
| Slope |
Rising, Falling, Rising & Falling |
| Source |
CH1/CH2 /EXT/(EXT/5)/AC Line |
| Polarity |
+wid , -wid |
| Limit Range |
<, >, <>, >< |
| Source |
CH1/CH2 |
| Pulse Range |
2ns ~ 4.2s |
| Resolution |
1ns |
| Signal Standard |
NTSC, PAL, 720p/50, 720p/60, 1080p/50, 1080p/60,
1080i/50, |
| Source |
1080i/60, Custom
CH1/CH2 |
| Sync |
Any, Select |
| Trigger condition |
Line, Field |
| Slope |
Rising, Falling |
| Limit Range |
<, >, <>, >< |
| Source |
CH1/CH2 |
| Time Range |
2ns ~ 4.2s |
| Resolution |
1ns |
| Timeout Type |
Edge, State |
| Source |
CH1/CH2 |
| Slope |
Rising, Falling |
| Time Range |
2ns ~ 4.2s |
| Resolution |
1ns |
| Polarity |
+wid , -wid |
| Limit Range |
<, >, <>, >< |
| Source |
CH1/CH2 |
| Time Range |
2ns ~ 4.2s |
| Resolution |
1ns |
| Pattern Setting |
Invalid, Low, High |
| Logic |
AND, OR, NAND, NOR |
| Source |
CH1/CH2 |
| Limit Range |
<, >, <>, >< |
| Time Range |
2ns ~ 4.2s |
| Resolution |
1ns |
| Window Type |
Absolute, Relative |
| Source |
CH1/CH2 |
| Condition |
Start, Stop, Restart, No Ack, EEPROM, 7bits Address
& Data,
10bits Adress & Data, Data Length |
| Source(SDA/SCL) |
CH1, CH2 |
| Data format |
Hex |
| Limit Range |
EEPROM: =, >, < |
| Data Length |
EEPROM: 1byte
Addr & Data: 1~2byte
Data Length: 1~12byte |
| R/W bit |
Addr & Data: Read, Write, Do not care |
| Condition |
Data |
| Source(CS/CL/Data) |
CH1, CH2 |
| Data format |
Binary |
| Data Length |
4 ~ 96 bit |
| Bit Value |
0, 1, X |
| Bit Order |
LSB, MSB |
| Condition |
Start, Stop, Data, Parity Error |
| Source (RX/TX) |
CH1, CH2 |
| Data format |
Hex |
| Limit Range |
=, >, < |
| Data Length |
1byte |
| Data Width |
5 bit, 6 bit, 7 bit, 8 bit |
| Parity Check |
None, Odd, Even |
| Stop Bit |
1 bit, 1.5 bit, 2 bit |
| Idle Level |
High, Low |
| Baud(Selectable) |
600/1200/2400/4800/9600/19200/38400/57600/115
200bit/s |
| (Custom) |
300bit/s ~ 334000 bit/s |
| Signal |
CL, SDA |
| Address |
7bit, 10bit |
| Threshold Level |
-4.5~4.5div |
| List |
1~7 lines |
| Signal |
SCL, MISO, MOSI |
| Edge Select |
Rising, Falling |
| Idle Level |
Low, High |
| Bit Order |
MSB, LSB |
| Threshold Level |
-4.5~4.5 div |
| List |
1~7 lines |
| Signal |
RX, TX |
| Data Width |
5 bit, 6 bit, 7 bit, 8 bit |
| Parity Check |
None, Odd, Even |
| Stop Bit |
1 bit, 1.5 bit, 2 bit |
| Idle Level |
Low, High |
| Threshold Level |
-4.5~4.5 div |
| List |
1~7 lines |
| Source |
CH1, CH2, Math, Ref, History |
Number of
Measurements |
Display 5 measurements at the same time |
| Measurement Range |
Screen region, Gate region |
| Measurement Parameters (36 Types) |
| Vertical (Voltage) |
Vmax |
Highest value in input waveform |
| Vmin |
Lowest value in input waveform |
| Vpp |
Difference between maximum
and minimum data values |
| Vamp |
Difference between top and
base in a bimodal signal ,or
between max and min in an
unimodal signal |
| Vtop |
Value of most probable higher
state in a bimodal waveform |
| Vbase |
Value of most probable lower
state in a bimodal waveform |
| Mean |
Average of all data values |
| Vmean |
Average of data values in the
first cycle |
| stdev |
Standard deviation of all data
values |
| Vstd |
Standard deviation of all data
values in the first cycle |
| Vrms |
Root mean square of all data
values |
| Crms |
Root mean square of all data
values in the first cycle |
| FOV |
Overshoot after a falling edge;
(base-min)/Amplitude |
| FPRE |
Overshoot before a falling edge;
(max-top)/Amplitude |
| ROV |
Overshoot after a rising edge
;(max-top)/Amplitude |
| RPRE |
Overshoot before a rising edge;
(base-min)/Amplitude |
| Horizontal (Time) |
Period |
Period for every cycle in waveform
at the 50% level ,and positive slope |
| Freq |
Frequency for every cycle in waveform
at the 50% level ,and positive slope |
| +Wid |
Width measured at 50% level and
positive slope |
| -Wid |
Width measured at 50% level and
negative slope |
| Rise Time |
Duration of rising edge from 10-90% |
| Fall Time |
Duration of falling edge from 90-10% |
| Bwid |
Time from the first rising edge to the
last falling edge ,or the first falling edge
to the last rising edge at the 50% crossi |
| +Dut |
Ratio of positive width to period |
| -Dut |
Ratio of negative width to period |
| Delay |
Time from the trigger to the first transition
at the 50% crossing |
| Time@Level |
Time from trigger of each transition at a
specific level and slope, include: Current,
Max, Min, Mean, Std-dev |
| Delay |
Phase |
Calculate the phase difference between
two edges |
| FRR |
Time between the first rising edges of
the two channels |
| FRF |
Time from the first rising edge of channel A
,to the first falling edge of channel |
| FFR |
Time from the first falling edge of channel A
,to the first rising edge of channel |
| FFF |
Time from the first falling edge of channel A
,to the first falling edge of channel |
| LRR |
Time from the first rising edge of channel A
,to the last rising edge of channel B |
| LRF |
Time from the first rising edge of channel A
,to the last falling edge of channel B |
| LFF |
Time from the first falling edge of channel A
,to the last rising edge of channel B |
| Cursors |
Manual : Time X1, X2, (X1-X2), (1/ΔT) |
| Voltage Y1, Y2, (Y1-Y2) |
| Track: Time X1, X2, (X1-X2) |
| Statistics |
Current, Mean, Min, Max, Std-Dev, Count |
| Counter |
Hardware 6 bits counter (channels are selectable) |
| Operation |
+ , - , * , / , FFT , d/dt , ∫dt , √ |
| FFT window |
Rectangular, Blackman, Hanning, Hamming |
| FFT display |
Full Screen, Split |
| Decoding number |
2 |
| Channel |
1 |
Max.
Output Frequency |
25MHz |
| Sample Rate |
125 MSa/s |
| Frequency Resolution |
1 μHz |
| Frequency Accuracy |
±50 ppm |
| Vertical Resolution |
14 bits |
| Amplitude Range |
-1.5 ~ +1.5V ( 50Ω)
-3 ~ +3V (High-Z) |
| Waveform Type |
Sine, Square, Ramp, Pulse, DC, Noise, Cardiac, Gaus
Pulse, Exp Rise, Exp Fall, Arb |
| Output impedance |
50Ω±2% |
| Protection |
Short-Circuit Protection |
| Frequency |
1μHz ~ 25MHz |
Offset Accuracy (100
kHz) |
±(0.3dB*Offset Setting Value +1mVpp) |
Amplitude flatness
(100 kHz, 5Vpp) |
±0.3 dB |
| SFDR |
DC ~ 1 MHz -60dBc
1 MHz ~ 5 MHz -55dBc
5 MHz ~ 25 MHz -50dBc |
| HD |
DC-5 MHz -50dBc
5 MHz - 25MHz -45dBc |
| Frequency |
1μHz ~ 10MHz |
| Duty Cycle |
20% ~ 80% |
| Rise/Fall time |
< 24 ns (10% ~ 90%) |
Overshoot (1kHz,
1Vpp, Typical) |
< 3% |
| Pulse Width |
> 50ns |
| Jitter |
< 500ps + 10ppm |
| Frequency |
1μHz ~ 300kHz |
| Linearity(Typical) |
< 0.1% of Pk-Pk (Typical, 1 kHz, 1 Vpp, 100%
Symmetry) |
| Symmetry |
0% ~ 100%( Adjustable) |
| Offset range |
±1.5 V(50Ω)
±3 V(High-Z) |
| Accuracy |
±(|offset|*1%+3 mV) |
| Bandwidth |
>25MHz (-3dB) |
| Frequency |
1μHz ~ 5MHz |
| Wave Length |
16Kpts |
| Sample Rate |
125MSa/s |
| Lead in |
EasyWave |
| Standard |
USB Host, USB Device, LAN, Pass/Fail, Trigger Out |
| Pass/Fail |
3.3V TTL Output |
| Display Type |
8 inches TFT LCD |
| Display Resolution |
800×480 |
| Display Color |
|
| 24 bit |
|
| Contrast(Typical) |
500:1 |
| Backlight |
300nit |
| Display Mode |
Dot, Vector |
| Persist Time |
Off, 1 Sec, 5 Sec, 10 Sec, 30 Sec, Infinite |
| Color Display |
Normal, Color |
| Screen Saver |
1min, 5min, 10min, 30min, 1hour, Off |
| Language |
Simplified Chinese, Traditional Chinese, English,
French, Japanese, Korean, German, Russian, Italian,
Portuguese |
| Temperature |
Operating: 10℃～ +40℃
Non-operating:-20℃～ +60℃ |
| Humidity |
Operating: 85%RH, 40℃ , 24hours
Non-operating: 85%RH, 65℃ , 24 hours |
| Height |
Operating: ≤3000m
Non-operating: ≤15,266m |
Electromagnetic
Compatibility |
2004/108/EC),
Execution Standard EN 61326-1:2006
EN 61000-3-2:2006 + A2:2009, EN 61000-3-3:2008 |
| Safety |
2006/95/EC
Execution Standard EN 61010-1:2010/EN 61010-2-
030:2010 |
| Dimensions |
Length 340mm
Width 123mm
Height 184mm |
| Weight |
N.W: 3.26 Kg; G.W:4.25Kg |
| Input Voltage |
100 ~ 240 VAC, CAT II, Auto selection |
| Frequency |
50/60 /400Hz |
| Power |
50W Max |