Waveform Output |
Impedance |
50Ω(typical) |
Protection |
short-circuit protection |
Isolation |
Connector shells for channel output(s),Sync and Modulation input of BNC,isolated from BNC connector and chassis.Maximum allowable voltage on isolated connector shells is ±42Vpk. |
AM / DSB-AM Modulation ( CH1/CH2 ) |
Carrier |
Sine, Square, Ramp, Arbitrary(except DC) |
Source |
Internal/External |
Modulation waveform |
Sine, Square, Ramp, Noise, Arbitrary |
Modulation depth |
0%-120% |
Modulation Frequency |
1mHz-50kHz |
FM Modulation ( CH1/CH2 ) |
Carrier |
Sine, Square, Ramp, Arbitrary(except DC) |
Source |
Internal/External |
Modulation waveform |
Sine, Square, Ramp, Noise, Arbitrary |
Modulation Frequency |
1mHz-50kHz |
FM Modulation ( CH1/CH2 ) |
Carrier |
Sine, Square, Ramp, Arbitrary(except DC) |
Source |
Internal/External |
Modulation waveform |
Sine, Square, Ramp, Noise, Arbitrary |
Phase Deviation |
0-3600 ,0.1°Resolution |
Modulation Frequency |
1mHz-50kHz |
FSK Modulation ( CH1/CH2 ) |
Carrier |
Sine, Square, Ramp, Arbitrary(except DC) |
Source |
Internal/External |
Modulation waveform |
50% duty-cycle square waveform |
Modulation Frequency |
1mHz-1MHz |
ASK Modulation ( CH1/CH2 ) |
Carrier |
Sine, Square, Ramp, Arbitrary(except DC) |
Source |
Internal/External |
Modulation waveform |
50% duty-cycle square waveform |
Modulation Frequency |
1mHz-1MHz |
PWM Modulation ( CH1/CH2 ) |
Carrier |
Pulse |
Source |
Internal/External |
Modulation waveform |
Sine, Square, Ramp, Arbitrary(except DC) |
Modulation Frequency |
1mHz-50kHz |
Sweep ( CH1/CH2 ) |
Carrier |
Sine, Square, Ramp, Arbitrary(except DC) |
Type |
linear/logarithmic |
Direct |
Up/down |
Sweep time |
1 ms- 500 s±0.1% |
Trigger source |
Manual, external, internal |
Burst ( CH1/CH2 ) |
Waveform |
Sine, Square, Ramp, Pulse, Arbitrary(except DC) |
Carrier Frequency |
2mHz-100MHz |
Type |
Count(1 - 1,000,000 periods),infinite, Gated |
Start/Stop phrase |
00360 |
Internal period |
1 ps- 1000 s± 1% |
Trigger delay |
232ns-34s |
Gated source |
External trigger |
Trigger source |
Manual, External or Internal |
External modulation |
Connector |
Rear-panel BNC,isolated from chassis |
Voltage level |
±4.5Vpk= 100% modulation >5k0 input impedance |
Note |
The external input voltage can't be over ±5Vpk, otherwise instrument gets damaged. |
Trigger Input |
Connector |
Rear-panel BNC,chassis-referenced |
Input Level |
TTL compatible |
Slope |
Up or down (optional) |
Pulse width |
>5± ns |
Input impedance |
>5kΩ,DC coupling |
Reaction time |
380ns(typical) |
Trigger Output |
Connector |
Rear-panel BNC,chassis-referenced |
Voltage level |
TTL compatible |
Pulse width |
>60 ns(typical) |
Output impedance |
50Ωtypical) |
Max Frequency |
1 MHz |
SYNC Output |
Connector |
Rear-panel BNC,isolated from chassis |
Voltage level |
TTL compatible |
Pulse width |
>50 ns(typical) |
Output impedance |
50Ω(typical) |
Max Frequency |
2 MHz |
Frequency reference input |
Connector |
Rear-panel BNC,isolated from chassis and all connector. |
Frequency range |
10MHz±50Hz |
Voltage level |
2.3Vpp -3.3Vpp |
Lock time |
< 2 s |
Input impedance |
1KΩ AC-coupled |
Frequency reference output |
Connector |
Rear-panel BNC,chassis-referenced |
Frequency |
10MHz |
Voltage level |
>1Vpp |
Output impedance |
50Ω AC-coupled |