| Display |
| Screen size/type: |
16,5 cm (6,5“) VGA color display |
| Resolution: |
640 (H) x 480 (V) pixels |
| Backlight: |
400 cd/m2 (LED) |
| Display range in horizontal direction: |
without menu bar: 12 Div (600 pixels)
with menu bar: 10 Div (500 pixels) |
| Display range in vertical direction: |
8 Div (400 pixels) |
| with VirtualScreen usage: |
20 Div |
| Color depth: |
256 colors |
| Trace display: |
pseudo-color, inverse brightness |
| Levels of trace brightness: |
32 |
| Vertical System |
| DSO mode: |
CH1, CH2 |
| MSO mode (POD with logic probe R&S®HO3508) |
| R&S®HMO1002 series: |
CH1, POD, Ext.In oder CH1, CH2, |
| R&S®HMO1202 series: |
CH1, CH2, POD, Ext.In |
| Analog Channels |
| Y-bandwidth (-3 dB) |
| (1 mV, 2 mV)/Div |
| R&S®HMO1002 series: |
50 MHz |
| R&S®HMO1202 series: |
100 MHz |
| (5 mV bis 10 V)/Div |
| R&S®HMO1052: |
50 MHz |
| R&S®HMO1072: |
70 MHz |
| R&S®HMO1102: |
100 MHz |
| R&S®HMO1212: |
100 MHz |
| R&S®HMO1222: |
200 MHz |
| R&S®HMO1232: |
300 MHz |
| Lower AC bandwidth: |
2 Hz |
| Bandwidth limitation (switchable): |
about 20 MHz |
| Rise time (calculated, 10% to 90%) |
| R&S®HMO1052 (50 MHz): |
<7 ns |
| R&S®HMO1072 (70 MHz): |
<5 ns |
| R&S®HMO1102 (100 MHz): |
<3.5 ns |
| R&S®HMO1212 (100 MHz): |
<3.5 ns |
| R&S®HMO1222 (200 MHz): |
<1.75 ns |
| R&S®HMO1232 (300 MHz): |
<1.15 ns |
| DC gain accuracy (all ranges): |
3% of full scale |
| Input sensitivity range |
| all analog channels: |
1 mV/Div to 10 V/Div |
| coarse stepping: |
13 calibrated steps, 1-2-5 sequence |
| variable stepping: |
freely between calibrated steps |
| Impedance |
| R&S®HMO1002 series: |
1MΩ II 16pF ±2pF |
| R&S®HMO1202 series: |
1MΩ II 16pF ±2pF, 50Ω (switchable) |
| Coupling: |
DC, AC, GND |
| Max. input voltage |
| 1MΩ: |
200Vp (derates at 20db/decade to 5V above 100kHz) |
| 50Ω (R&S®HMO1202 series): |
5 Veff, max. 30 Vs |
| Position range |
| R&S®HMO1002 series: |
±5Div (from center of screen) |
| R&S®HMO1202 series: |
±15Div (from center of screen) |
| Channel isolation: |
35 dB from DC to specified bandwidth (same V/Div range) |
| XY mode: |
CH1, CH2 |
| Inversion: |
selectively all analog channels |
| Logic Channels with Logic Probe R&S®HO3508 |
| Thresholds: |
TTL, CMOS, ECL, user-definied (-2 V to +8 V) |
| Impedance: |
100kΩ || 4pF |
| Coupling: |
DC |
| Max. input voltage: |
40Vp |
| Trigger System |
| Trigger Mode |
| Auto: |
triggers automatically also without any specific trigger event |
| Normal: |
triggers only on specific trigger events |
| Single: |
triggers once on a trigger event |
| Trigger indicator: |
screen and panel (LED) |
| Trigger sensitivity |
| up to 5mV/Div: |
1.5 Div |
| from 5mV/Div: |
0.8 Div |
| Trigger level setting |
| with auto level: |
adjustable between peak values of a signal |
| without auto level: |
±5Div (from center of screen) |
| External: |
-5 V to +5 V |
| Trigger Coupling |
| AC |
| R&S®HMO1002 series: |
<5 mV/Div: 10 Hz to 65 MHz
>5 mV/Div: 10 Hz to 65/90/130 MHz |
| R&S®HMO1202 series: |
<5 mV/Div: 10 Hz to 130 MHz
>5 mV/Div: 10 Hz to 130/220/300 MHz |
| DC |
| R&S®HMO1002 series: |
<5 mV/Div: DC to 65 MHz
>5 mV/Div: DC to 65/90/130 MHz |
| R&S®HMO1202 series: |
<5 mV/Div: DC to 130 MHz
>5 mV/Div: DC to 130/220/300 MHz |
| HF |
| R&S®HMO1002 series: |
<5 mV/Div: 30 kHz to 65 MHz
>5 mV/Div: 30 kHz to 65/90/130 MHz |
| R&S®HMO1202 series: |
<5 mV/Div: 30 kHz to 130 MHz
>5 mV/Div: 30 kHz to 130/220/300 MHz |
| Selectable filters |
| LF: |
DC to 5 kHz (-3 db), selectable in DC and auto level mode |
| Noise rejection: |
min. level: 1.5 Div (> 5 mV/Div) selectable with AC, DC and HF coupling |
| Trigger hold-off: |
auto, 50 ns to 10 s |
| External Input (BNC) |
| Function: |
ext. trigger input, additional digital channel |
| Impedance: |
1MΩ || 16pF ±2pF |
| Acurracy: |
300 mVss |
| Trigger level range: |
-5 V bis +5 V |
| Max. input voltage: |
100 Vs (derates at 20 db/decade to 5 V above 100 kHz) |
| Trigger coupling |
| AC |
| R&S®HMO1002 series: |
10 Hz to 50/70/100 MHz |
| R&S®HMO1202 series: |
10 Hz to 100/200/300 MHz |
| DC |
| R&S®HMO1002 series: |
DC to 50/70/100 MHz |
| R&S®HMO1202 series: |
DC to 100/200/300 MHz |
| Trigger Output via AUX OUT (BNC) |
| Functions: |
Pulse output for every acquisition trigger event, error output on mask violation |
| Output level: |
approx. 3 V |
| Pulse polarity: |
positive |
| Pulse width: |
>150 ns (trigger event),
>0.5 µs (mask violation) |
| Trigger Types |
| Edge |
| Direction: |
rising, falling, both |
| Trigger coupling: |
auto level AC, DC, HF |
| Switchable filters: |
LF, noise rejection |
| Sources |
| R&S®HMO1002: |
all analog and digital channels, AC line, external (AC, DC) |
| R&S®HMO1202: |
all analog and digital channels, AC line, external (AC, DC) |
| Pulse Width |
| Polarity: |
positive, negative |
| Functions: |
equal, not equal, lower, higher, within/without a range |
| Pulse duration: |
16ns to 10s, resolution min. 2ns |
| Sources: |
all analog channels |
| Logic |
| Functions |
| Boolean operators: |
and, or, true, false |
| Time based operators: |
equal, not equal, lower, higher, within/without a time range, timeout |
| Duration: |
16 ns to 10 s, resolution min. 2 ns |
| States: |
H, L, X |
| Sources: |
all logic channels |
| Video |
| Sync. pulse polarity: |
positive, negative |
| Supported standards: |
NTSC, SECAM, PAL, PAL-M, SDTV 576i, HDTV 720p, HDTV 1080i, HDTV 1080p |
| Field: |
even/odd, either |
| Line: |
line number selectable, all |
| Sources: |
all analog channels, external (AC, DC) |
| Serial Busses (optional) |
| Bus representation: |
Up to two busses can be analyzed at the same time. Color-coded display of decoded data in ASCII, binary, decimal and hexadecimal format. |
| Option / Voucher codes |
| R&S®HOO10, R&S®HV110: |
Analysis of I2C, SPI, UART/RS-232 signals on analog and logic channels |
| R&S®HOO11, R&S®HV111: |
Analysis of I2C, SPI, UART/RS-232 signals on all analog channels |
| R&S®HOO12, R&S®HV112: |
Analysis of CAN and LIN signals on analog and logic channels |
| Trigger types by protocols |
| I2C: |
Start, Stop, ACK, NACK, Address/Data |
| SPI: |
Start, End, Serial Pattern (32 Bit) |
| UART/RS-232: |
Startbit, Frame Start, Symbol, Pattern |
| LIN: |
Frame Start, Wake Up, Identifier, Data, Error |
| CAN: |
Frame Start, Frame End, Identifier, Data, Error |
| Horizontal System |
| Time domain (Yt): |
main screen, time domain and zoom window |
| Frequency domain (FFT): |
time domain and frequency domain window (FFT) |
| XY mode: |
voltage (XY) |
| VirtualScreen: |
virtual display of ±10Div for all math, logic, bus, reference signals |
| Component tester: |
voltage (X), current (Y) |
| Reference signals: |
up to 4 references |
| Channel deskew: |
±32ns, step size 2 ns |
| Memory zoom: |
up to 50.000:1 |
| Time base |
| Accuracy: |
±50.0x10-6 |
| Aging: |
±10.0x10-6 per year |
| Operation modes |
| Refresh |
| R&S®HMO1002 series: |
2 ns/Div to 50 s/Div |
| R&S®HMO1202 series: |
1 ns/Div to 50 s/Div |
| ROLL: |
50 ms/Div to 50 s/Div |
| Acquisition System |
| Realtime Sampling Rate |
| Analog channels |
| R&S®HMO1002 series: |
2x 500 MSa/s or 1x 1 GSa/s |
| R&S®HMO1202 series: |
2x 1 GSa/s or 1x 2 GSa/s |
| Logic channels |
| R&S®HMO1002 series: |
8x 500 MSa/s |
| R&S®HMO1202 series: |
8x 1 GSa/s |
| Memory depth |
| Analog channels |
| R&S®HMO1002 series: |
2x 500 kSa or 1x 1 MSa |
| R&S®HMO1202 series: |
2x 1 MSa or 1x 2 MSa |
| Logic channels |
| R&S®HMO1002 series: |
500 kSa per channel |
| R&S®HMO1202 series: |
1 MSa per channel |
| Resolution: |
8 Bit, (HiRes up to 16Bit) |
| Waveform arithmetics: |
refresh, roll (loose/triggered), average (up to 1024), envelope, peak detect (2 ns), filter (low-pass, adjustable), high resolution (up to 16 bit) |
| Record modes: |
automatic, max. sampling rate, max. waveform rate |
| Interpolation |
| All analog channels: |
sin(x)/x, linear, sample-hold |
| Logic channels: |
pulse |
| Delay |
| Pre-trigger |
| R&S®HMO1002 series: |
0 to 500.000 Sa x (1/sample rate) |
| R&S®HMO1202 series: |
0 to 1.000.000 Sa x (1/sample rate) (multiplied by 2 in interlaced mode) |
| Post-trigger: |
0 to 8x10 6 Sa x (1/sample rate) |
| Waveform update rate: |
up to 10,000 Wfm/s |
| Waveform display: |
dots, vectors, persistence afterglow |
| Persistence afterglow: |
min. 50 ms |
| Waveform Measurements and Operation |
| Operation: |
menu-driven (multilingual), auto-set, help functions (multilingual) |
| Automatic measurements: |
voltage (Vpp, Vp+, Vp-, Vrms, Vavg, Vmin, Vmax), amplitude, phase, frequency, period, rise/fall time (80%, 90%), pulse width (pos/neg), burst width, duty cycle (pos/neg), standard deviation, delay, crest factor, overshoot (pos/ neg), edge/pulse count (pos/neg), trigger period, trigger frequency |
| Cursor measurements: |
voltage (V1, V2, ∆V), time (t1, t2, ∆t, 1/∆t), ratio X, ratio Y, pulse and edge count (pos/ neg), peak values (Vpp, Vp+, Vp-), Vmean, Vrms, standard deviation, duty cycle (pos/neg), rise/ fall time (80%, 90%), ratio marker, crest factor |
| Quick measurements (QUICKVIEW): |
voltage (Vpp, Vp+, Vp-, Vrms, Vmean), rise/fall time, frequency, period plus 6 additional measurement functions (see automatic measurement functions, freely selectable) |
| Marker: |
up to 8 freely positionable markers for easy navigation |
| Frequency Counter (hardware based) |
| Resolution: |
5 digit |
| Frequency range |
| R&S®HMO1002: |
0.5 Hz bis 50/70/100 MHz |
| R&S®HMO1202: |
0.5 Hz bis 100/200/300 MHz |
| Accuracy: |
±50.0 x 10-6 |
| Aging: |
±10.0 x 10-6 per year |
| Mask Testing |
| Functions: |
Pass/Fail comparison with an user-definied mask performed on waveforms |
| Sources: |
all analog channels |
| Mask definition: |
Mask enclosing acquired waveform with user-defined tolerance |
| Actions |
| on mask violations: |
beep, acquisition stop, screenshot, trigger pulse, automatically saving trace data |
| during acquisiton: |
statistics: number of completed tests, number of passes / failed acquisitions (absolute and in percent), test duration |
| Waveform Maths |
| Quickmath |
| Functions: |
addition, substraction, multiplication, division |
| Sources: |
CH1, CH2 |
| Mathematics (R&S®HMO1202 series) |
| Functions: |
addition, substraction, multiplication, division, minimum / maximum, square, square root, absolute value, pos/neg wave, reciprocal, inverse, log10/ln, derivation, integration, filter (lowpass/highpass) |
| Editing: |
formula editor, menu-driven |
| Sources: |
all analog channels, user-defined constants |
| Storage location: |
math. memory |
| Number of formula sets: |
5 formula sets |
| Number of equations: |
5 equations per formula set |
| Simultaneous display of math. functions: |
1 formula set with max. 4 equations |
| Frequency Analysis (FFT) |
| Parameters: |
frequency span, center frequency, vertical scale, vertical position |
| FFT length: |
2 Kpts, 4 Kpts, 8 Kpts, 16 Kpts, 32 Kpts, 64 Kpts, 128 Kpts |
| Window: |
Hanning, Hamming, Rectangular, Blackman |
| Scale: |
dBm, dBV, Vrms |
| Waveform arithmetics: |
refresh, envelope, average (up to 512) |
| Cursor measurement: |
2 horizontal cursors, previous / next peak search |
| Sources: |
all analog channels |
| Probe Adjust Output |
| Operation: |
manual, adjust-wizzard |
| Frequence: |
1 kHz, 1 MHz |
| Level |
| R&S®HMO1002 series: |
approx. 2.5 Vpp (ta<4 ns) |
| R&S®HMO1202 series: |
approx. 2.5 Vpp (ta<1 ns) |
| Pattern Generator |
| Functions : |
square wave / probe adjust, bus signal source, counter, programmable pattern |
| Square wave (Probe ADJ output): |
frequency range: <1 mHz to 500 kHz level: 2.5 Vpp (ta <4 ns) polarity: normal, invert duty cycle: 1% to 99% |
| Bus Signal Source (4 Bit): |
I2C (100 kBit/s, 400 kBit/s, 1 MBit/s), SPI (100 kBit/s, 250 kBit/s, 1 MBit/s), UART (9600 Bit/s, 115,2 kBit/s, 1 MBit/s), CAN (up to 50 MBits/s), LIN (up to 50 MBits/s) |
| Counter (4 Bit): |
frequency: <1 mHz to 25 MHz direction: incrementing, decrementing |
| Programmable pattern (4 Bit): |
sampling time: 20 ns to 42 s
memory depth: 2048 sa
pattern idle time: 20 ns to 42 s |
| Function Generator |
| Waveform modes: |
DC, sine, square, triangle/ramp, pulse |
| Sine: |
frequency range: 0.1 Hz to 50 kHz
flatness: ±1 dB relative to 1 kHz
DC offset: max. ±3 V |
| Square: |
frequency range: 0.1 Hz to 25 kHz
rise time: <4 µs
DC offset: max. ±3 V |
| Triangle / Ramp : |
frequency range: 0,1 Hz bis 10 kHz
DC offset: max. ±3 V |
| Pulse: |
frequency range: 0.1 Hz to 10 kHz
duty cycle: 10% to 90%
DC offset: max. ±3 V |
| Sampling rate: |
978 kSa/s |
| Frequency accuracy: |
±50.0 x 10-6 |
| Aging: |
±10.0 x 10-6 per year |
| Amplitude |
| DC: |
±3 V |
| high impedance load: |
60 mVpp to 6 Vpp |
| 50 Ω load: |
30 mVpp to 3 Vpp |
| Accuracy: |
3% |
| Digital Voltmeter |
| Display (3-digit): |
Primary and secondary measurement value per channel, simultaneous measuring on all channels |
| Functions: |
DC, DCrms, ACrms, Vpp, Vp+, Vp-, crest factor |
| Sources: |
all analog channels |
| Component Tester |
| Parameters: |
voltage (X), current (Y) |
| Testing frequency: |
50 Hz, 200 Hz |
| Voltage: |
10 Vp (open) |
| Current: |
10 mA (short) |
| Reference potential: |
Ground (PE) |
| Interfaces |
| for mass storage (FAT16/32): |
1x USB host (type A), max. 500 mA |
| for remote control: |
Ethernet (RJ45), USB device (type B) |
| General Data |
| Application memory: |
3 MB for references and device settings |
| Save / Recall |
| device settings: |
on internal file system or external USB memory, available file formats: SCP, HDS |
| reference waveforms: |
on internal file system or external USB memory, available file formats: BIN (MSB/LSB), FLT (MSB/LSB), CSV, TXT, HRT |
| traces: |
on external USB memory, available file formats: BIN (MSB/LSB), FLT (MSB/LSB), CSV, TXT |
| data: |
display or acquisition data |
| sources: |
single or all analog channels |
| screenshots: |
on external USB memory, available file formats: BMP, GIF, PNG (color, inverted, grey-scale) |
| Realtime clock (RTC): |
date and time |
| Power supply |
| AC supply: |
100 V to 240 V, 50 Hz to 60 Hz, CAT-II |
| power consumption |
| R&S®HMO1002: |
max. 25 W |
| R&S®HMO1202: |
max. 30 W |
| Safety: |
in line with IEC 61010-1 (ed. 3), IEC 61010-2- 30 (ed. 1), EN 61010-1, EN 61010-2-030 , CAN/CSA-C22.2 No. 61010-1-12 , CAN/ CSA-C22.2 No. 61010-2-030-12 ,UL Std. No. 61010-1 (3rd Edition) , UL61010-2-030 |
| Temperature |
| operating temp. range: |
+5 °C to +40 °C |
| storage temperature range: |
-20 °C to +70 °C |
| Rel. humidity: |
5% to 80% (without condensation) |
| Mechanical data |
| dimensions (W x H x D): |
285 x 175 x 140 mm |
| net weight: |
2.5 kg |
| EMC |
| RF emission: |
in line with CISPR 11/EN 55011 class B |
| Immunity: |
in line with IEC/EN 61326-1 table 2, immunity test requirements for industrial environments. Test criterion is displayed noise level within ±1 div for 5 mV/div input sensitivity |