| |
DS2072 |
DS2102 |
DS2202 |
| Analog BW |
70 MHz |
100MHz |
200 MHz |
| Channels |
2 |
| Sample Rate (Max. ) |
2GSa/s (single-channel), 1GSa/s (dual-channel) |
| Memory Depth (Max. ) |
14Mpts (Std.), 56Mpts(Opt.) |
| Waveform Capture Rate |
50,000 wfms/s (Max. ) |
| Vertical Scale |
500 uV/div to 10 V/div |
| Realtime Waveform Recorded |
Max. 65,000 frames (Std.) |
| Standard Probe |
RP3300 350MHz BW Passive Probe: 2 sets |
| Complete Specifications |
| Sample Mode |
Real-time sample |
| Real Time |
2 GSa/s (single-channel) |
| Sample Rate |
1 GSa/s (dual-channel) |
| Peak Detect |
500 ps (single-channel)
1 ns (dual-channel) |
| Averaging |
After both channels finish N samples at the same time, N can be 2, 4, 8, 16, 32, 64, 128, 256, 512, 1024, 2048, 4096 or 8192. |
| High Resolution |
12 bit of resolution When ≤5 µs/div @ 1 GSa/s (or =10 µ;s/div @ 500 MSa/s). |
| Memory Depth |
Single-channel: Auto, 14k pts, 140k pts, 1.4M pts, 14M and 56M pts (option) are available Dual-channel: Auto, 7k pts, 70k pts, 700k pts, 7M pts and 28M pts (option) are available |
| Number of Channels |
dual-channel |
| Input Coupling |
DC, AC or GND |
| Input Impedance |
(1MΩ±1%) || (16 pF±3 pF) |
| Probe Attenuation |
0.01X-1000X 1-2-5 step |
| Coefficient |
|
| Max Input |
Maximum input voltage of the analog channel |
| Voltage (1MΩ) |
CAT I 300 Vrms, CAT II 100 Vrms, transient overvoltage 1000 Vpk
With RP2200 10:1 probe: CAT II 300 Vrms
With RP3300 10:1 probe: CAT II 300 Vrms
With RP3500 10:1 probe: CAT II 300 Vrms
With RP5600 10:1 probe: CAT II 300 Vrms |
| Time Base Scale |
5 ns/div to 1000 s/div |
2 ns/div to 1000 s/div |
| Time Base Accuracy 1 |
≤ ± 25 ppm |
| Clock Drift |
≤ ± 5 ppm/year |
| Max Delay Range |
Pre-trigger (negative delay): ≥1 screen width
Post-trigger (positive delay): 1 s to 100,000 s |
| Time Base Mode |
Y-T, X-Y, Roll, Delayed |
| Number of X-Ys |
1 path |
| Waveform Capture |
50,000 wfms/s (dots display) |
| Rate 2 |
|
| Bandwidth (-3dB) |
DC to 70 MHz |
DC to 100 MHz |
DC to 200 MHz |
| Single Bandwidth |
DC to 70 MHz |
DC to 100 MHz |
DC to 200 MHz |
| Vertical Resolution |
8 bit |
| Vertical Scale |
500 uV/div to 10 V/div |
| Offset Range |
500 uV/div to 50 mV/div: ± 2 V
51 mV/div to 200 mV/div: ± 10 V
205 mV/div to 2 V/div: ± 50 V
2.05 V/div to 10 V/div: ± 100 V |
| Bandwidth Limit 1 |
20 MHz |
20 MHz |
20 MHz/100 MHz |
| Low Frequency |
≤ 5 Hz (on BNC) |
| Response |
|
| (AC coupling, -3dB) |
|
| Rise Time |
5 ns |
3.5 ns |
1.8 ns |
| DC Gain Accuracy |
±2% full scale |
| DC Offset Accuracy |
±0.1 div ± 2 mV ± 1% offset |
| Channel to Channel |
DC to maximum bandwidth: >40 dB |
| Isolation |
|
| Trigger Level |
Internal ±5 div from the center of the screen |
| Range |
EXT ± 4 V |
| Trigger Mode |
Auto, Normal, Single |
| Holdoff Range |
100 ns to 10 s |
| High |
75 kHz |
| Frequency |
|
| Rejection 1 |
|
| Low |
75 kHz |
| Frequency |
|
| Rejection 1 |
|
| Trigger Sensitivity |
1div (below 10mV or noise rejection is enabled)
0.3div (above 10mV and noise rejection is disabled) |
| Edge Trigger |
|
| Edge Type |
Rising, Falling, Rising & Falling |
| Pulse Trigger |
|
| Pulse |
Positive Pulse Width (greater than, lower than, within specified interval) |
| Condition |
Negative Pulse Width (greater than, lower than, within specified interval) |
| Pulse Width Range |
2 ns to 4 s |
| Runt Trigger |
|
| Pulse |
None, > (greater than), < (lower than), |
| Condition |
<> (within the specified interval) |
| Polarity |
Positive, Negative |
| Pulse Width Range |
2 ns to 4 s |
| Runt Trigger |
|
| Windows Type |
Rising, Falling, Rising&Falling |
| Trigger Position |
Enter, Exit, Time |
| Windows Time |
16 ns to 4 s |
| Nth Edge Trigger |
|
| Edge Type |
Rising, Falling |
| Idle Time |
16 ns to 10 s |
| Number of Edges |
1 to 65, 535 |
| Slope Trigger |
| Slope Condition |
Positive Slope (greater than, lower than, within specified interval)
Negative Slope (greater than, lower than, within specified interval) |
| Time Setting |
2 ns to 4 s |
| Video Trigger |
|
| Signal Standard |
Support standard NTSC, PAL and SECAM broadcasting standards
Support 480P, 576P, 720P, 1080P and 1080I HDTV standards |
| Pattern Trigger |
|
| Pattern Setting |
H, L, X, Rising Edge, Falling Edge |
| Delay Trigger |
|
| Edge Type |
Rising, Falling |
| Delay Type |
> (greater than), < (lower than), <> (within the specified interval), >< (outside the specified interval) |
| Delay Time |
2 ns to 4 s |
| TimeOut Trigger |
|
| Edge Type |
Rising, Falling, Rising&Falling |
| TimeOut Value |
16 ns to 4 s |
| Duration Trigger |
| Pattern Setting |
H, L, X |
| Trigger Condition |
> (greater than), < (lower than), <> (within the specified interval) |
| Duration |
2 ns to 4 s |
| Setup/Hold Trigger |
| Edge Type |
Rising, Falling |
| Data Pattern |
H, L |
| Setup Time |
2 ns to 1 s |
| Hold Time |
2 ns to 1 s |
| RS232/UART Trigger |
| Polarity |
Negative, Positive |
| Trigger Condition |
Start, Error, Check Error, Data |
| Baud |
2400bps, 4800bps, 9600bps, 19200bps, 38400bps, 57600bps, 115200bps, User |
| Data Bits |
5 bit, 6 bit, 7 bit, 8 bit |
| I2C Trigger |
| Trigger Condition |
Start, Restart, Stop, Missing Ack, Address, Data, A&D |
| Address Bits |
7 bit, 10 bit |
| Address Range |
0 to 127, 0 to 1023 |
| Byte Length |
1 to 5 |
| SPI Trigger |
| Trigger Condition |
TimeOut |
| Timeout Value |
100 ns to 1 s |
| Data Bits |
4 bit to 32 bit |
| Data Line Setting |
H, L, X |
| USB Trigger |
| Signal Speed |
Low Speed, Full Speed |
| Trigger Condition |
SOP, EOP, RC, Suspend, ExitSuspend |
| Math |
| Waveform |
A+B, A-B, A°CB, A/B, FFT, Editable Advanced |
| Operation |
Operation, Logic Operation |
| FFT Window |
Operation, Logic Operation Rectangle, Hanning, Blackman, Hamming |
| FFT Display |
Operation, Logic Operation Split, Full Screen |
| FFT Vertical |
Linear Vrms, dBV rms |
| Scale |
| Logic Operation |
AND, OR, NOT, XOR |
| Math Function |
Intg, Diff, Log, Exp, Sqrt, Sine, Cosine, Tangent |
| Number of Buses for Decoding |
2 |
| Decoding Type |
Parallel (standard), RS232/UART (option), I2C (option), SPI (option) |
| Display |
| Display Type |
8.0 inches (203 mm) TFT LCD display |
| Display Resolution |
800 horizontal°CRGB°C480 vertical pixel |
| Display Color |
160,000 Color (TFT) |
| Persistence Time |
Min, 50 ms, 100 ms, 200 ms, 500 ms, 1 s, 2 s, 5 s, 10 s, 20 s, Infinite |
| Display Type |
Dots, Vectors |
| Real-time Clock |
Time and Date (user adjustable) |
| I/O |
| Standard Ports |
USB HOST (support USB-GPIB), USB DEVICE, LAN, Aux Output (TrigOut /PassFail) |
| Printer |
PictBridge |
| Compatibility |
| Probe Compensation |
Output |
| Output Voltage 1 |
About 3 V, peak-peak |
| Frequency 1 |
1 kHz |
| Power |
| Power Voltage |
100-240 V, 45-440 Hz |
| Power |
Maximum 50 W |
| Fuse |
2 A, T degree, 250 V |
| Environment |
| Temperature Range |
In operation: 0 °C to +50 ° C
Out of operation: -20 °C to +70 °C |
| Cooling Method |
Fan |
| Humidity Range |
Under +35 °C : ≤90 % relative humidity
+35 °C to +50 °C : =60 % relative humidity |
| Altitude |
In operation: under 3,000 meters |
| Out of operation |
under 15,000 meters |
| Mechanical |
| Dimensions 3 |
Width°CHeight°CDepth =361.6 mm°C 179.6 mm°C130.8 mm |
| Weight 4 |
Without package 3.9 kg °C 0.2 kg
With package 4.5 kg °C 0.5 kg |
| Adjustment Interval |
| The recommended calibration interval is one year.% |