Trigger |
Trigger Level Range |
Internal |
±5 div from center of the screen |
EXT |
±4 V |
Trigger Mode |
Auto, Normal, Single |
Holdoff Range |
100 ns to 10 s |
High Frequency Rejection [1] |
75 kHz |
Low Frequency Rejection [1] |
75 kHz |
Trigger Sensitivity |
1 div (below 10 mV or noise rejection is enabled)
0.3 div (above 10 mV and noise rejection is disabled) |
Edge Trigger |
Edge Type |
Rising, Falling, Rising/Falling |
Pulse Trigger |
Pulse Condition |
Positive Pulse Width
(greater than, lower than, within specific interval)
Negative Pulse Width
(greater than, lower than, within specific interval) |
Pulse Width Range |
2 ns to 4 s |
Runt Trigger |
Pulse Condition |
None, >, <, <> |
Pulse Polarity |
Positive, Negative |
Pulse Range |
2 ns to 4 s |
Windows Trigger (Option) |
Windows Type |
Rising, Falling, Rising/Falling |
Trigger Position |
Enter, Exit, Time |
Windows Time |
16 ns to 4 s |
Nth Edge Trigger (Option) |
Edge Type |
Rising, Falling |
Idle Time |
16 ns to 4 s |
Number of Edges |
1 to 65535 |
Slope Trigger |
Slope Condition |
Positive Slope (greater than, lower than, within specific interval)
Negative Slope (greater than, lower than, within specific interval) |
Time Setting |
10 ns to 1 s |
Video Trigger (HDTV Option) |
|
Signal Standard |
NTSC, PAL/SECAM, 480P, 576P (option), 720P, 1080P and 1080I (option) |
Pattern Trigger |
Pattern Setting |
H, L, X, Rising Edge, Falling Edge |
Delay Trigger (Option) |
Edge Type |
Rising, Falling |
Delay Type |
>, <, <>, >< |
Delay Time |
2 ns to 4 s |
TimeOut Trigger (Option) |
Edge Type |
Rising, Falling, Rising/Falling |
Timeout time |
16 ns to 4 s |
Duration Trigger (Option) |
Pattern Setting |
H, L, X |
Trigger Condition |
>, <, <> |
Duration Time |
2 ns to 4 s |
Setup/Hold Trigger |
Edge Type |
Rising, Falling |
Data Type |
H, L |
Setup Time |
2 ns to 1 s |
Hold Time |
2 ns to 1 s |
RS232/UART Trigger |
Polarity |
Normal, Invert |
Trigger Condition |
Start, Error, Check Error, Data |
Baud |
2400 bps, 4800 bps, 9600 bps, 19200 bps, 38400 bps, 57600 bps, 115200 bps, User |
Data Bits |
5 bit, 6 bit, 7 bit, 8 bit |
I2C Trigger |
Trigger Condition |
Start, Restart, Stop, Missing ACK, Address, Data, A&D |
Address Bits |
7 bit, 8 bit, 10 bit |
Address Range |
0 to 127, o to 255, 0 to 1023 |
Byte Length |
1 to 5 |
SPI Trigger |
Trigger Condition |
Timeout |
Timeout Value |
100 ns to 1 s |
Data Bits |
4 bit to 32 bit |
Data Setting |
H, L, X |
CAN Trigger (Option) |
Signal Type |
Rx, Tx, CAN_H, CAN_L, Differential |
Trigger Condition |
SOF, EOF, Frame Type, Frame Error |
Baud |
10 kbps, 20 kbps, 33.3 kbps, 50 kbps, 62.5 kbps, 83.3 kbps, 100 kbps, 125 kbps, 250 kbps, 500 kbps, 800 kbps, 1 Mbps, User |
Sample Point |
5% to 95% |
Frame Type |
Data, Remote, Error, Over Load |
Error Type |
Bit Fill, Answer Error, Check Error, Format Error, Random Error |
USB Trigger (Option) |
|
Signal Speed |
Low Speed, Full Speed |
Trigger condition |
SOP, EOP, RC, Suspend, Exit Suspend |