| Trigger |
| Trigger Level Range |
Internal |
±5 div from center of the screen |
| EXT |
±4 V |
| Trigger Mode |
Auto, Normal, Single |
| Holdoff Range |
100 ns to 10 s |
| High Frequency Rejection [1] |
75 kHz |
| Low Frequency Rejection [1] |
75 kHz |
| Trigger Sensitivity |
1 div (below 10 mV or noise rejection is enabled)
0.3 div (above 10 mV and noise rejection is disabled) |
| Edge Trigger |
| Edge Type |
Rising, Falling, Rising/Falling |
| Pulse Trigger |
| Pulse Condition |
Positive Pulse Width
(greater than, lower than, within specific interval)
Negative Pulse Width
(greater than, lower than, within specific interval) |
| Pulse Width Range |
2 ns to 4 s |
| Runt Trigger |
| Pulse Condition |
None, >, <, <> |
| Pulse Polarity |
Positive, Negative |
| Pulse Range |
2 ns to 4 s |
| Windows Trigger (Option) |
| Windows Type |
Rising, Falling, Rising/Falling |
| Trigger Position |
Enter, Exit, Time |
| Windows Time |
16 ns to 4 s |
| Nth Edge Trigger (Option) |
| Edge Type |
Rising, Falling |
| Idle Time |
16 ns to 4 s |
| Number of Edges |
1 to 65535 |
| Slope Trigger |
| Slope Condition |
Positive Slope (greater than, lower than, within specific interval)
Negative Slope (greater than, lower than, within specific interval) |
| Time Setting |
10 ns to 1 s |
| Video Trigger (HDTV Option) |
|
| Signal Standard |
NTSC, PAL/SECAM, 480P, 576P (option), 720P, 1080P and 1080I (option) |
| Pattern Trigger |
| Pattern Setting |
H, L, X, Rising Edge, Falling Edge |
| Delay Trigger (Option) |
| Edge Type |
Rising, Falling |
| Delay Type |
>, <, <>, >< |
| Delay Time |
2 ns to 4 s |
| TimeOut Trigger (Option) |
| Edge Type |
Rising, Falling, Rising/Falling |
| Timeout time |
16 ns to 4 s |
| Duration Trigger (Option) |
| Pattern Setting |
H, L, X |
| Trigger Condition |
>, <, <> |
| Duration Time |
2 ns to 4 s |
| Setup/Hold Trigger |
| Edge Type |
Rising, Falling |
| Data Type |
H, L |
| Setup Time |
2 ns to 1 s |
| Hold Time |
2 ns to 1 s |
| RS232/UART Trigger |
| Polarity |
Normal, Invert |
| Trigger Condition |
Start, Error, Check Error, Data |
| Baud |
2400 bps, 4800 bps, 9600 bps, 19200 bps, 38400 bps, 57600 bps, 115200 bps, User |
| Data Bits |
5 bit, 6 bit, 7 bit, 8 bit |
| I2C Trigger |
| Trigger Condition |
Start, Restart, Stop, Missing ACK, Address, Data, A&D |
| Address Bits |
7 bit, 8 bit, 10 bit |
| Address Range |
0 to 127, o to 255, 0 to 1023 |
| Byte Length |
1 to 5 |
| SPI Trigger |
| Trigger Condition |
Timeout |
| Timeout Value |
100 ns to 1 s |
| Data Bits |
4 bit to 32 bit |
| Data Setting |
H, L, X |
| CAN Trigger (Option) |
| Signal Type |
Rx, Tx, CAN_H, CAN_L, Differential |
| Trigger Condition |
SOF, EOF, Frame Type, Frame Error |
| Baud |
10 kbps, 20 kbps, 33.3 kbps, 50 kbps, 62.5 kbps, 83.3 kbps, 100 kbps, 125 kbps, 250 kbps, 500 kbps, 800 kbps, 1 Mbps, User |
| Sample Point |
5% to 95% |
| Frame Type |
Data, Remote, Error, Over Load |
| Error Type |
Bit Fill, Answer Error, Check Error, Format Error, Random Error |
| USB Trigger (Option) |
|
| Signal Speed |
Low Speed, Full Speed |
| Trigger condition |
SOP, EOP, RC, Suspend, Exit Suspend |