| General Specifications |
| Model |
DG1032Z |
DG1062Z |
| Channel |
2 |
2 |
| Max Frequency |
30 MHz |
60 MHz |
| Sample Rate |
200 MSa/s |
| Waveform |
| Basic Waveform |
Sine, Square, Ramp, Pulse, Noise |
| Built-in Arbitrary Waveform |
160 kinds, including Sinc, Exponential Rise, Exponential Fall, ECG, Gauss, HaverSine, Lorentz, Dual-Tone, DC Voltage, etc. |
| Frequency Characteristics |
| Sine |
1 µHz to 30 MHz |
1 µHz to 60MHz |
| Square |
1 µHz to 15 MHz |
1 µHz to 25 MHz |
| Ramp |
1 µHz to 500kHz |
1 µHz to 1MHz |
| Pulse |
1 µHz to 15 MHz |
1 µHz to 25 MHz |
| Harmonic |
1uHz to 10MHz |
1uHz to 20MHz |
| Noise (-3dB) |
30 MHz bandwidth |
60 MHz bandwidth |
| Arbitrary Waveform |
1 µHz to 10 MHz |
1 µHz to 20 MHz |
| Resolution |
1 µHz |
| Accuracy |
±1 ppm of the setting value, 18° to 28° |
| Sine Wave Spectrum Purity |
| Harmonic Distortion |
Typical (0 dBm)
DC-10 MHz (included): <-65 dBc
10 MHz to 30 MHz (included): <-55 dBc
30 MHz to 60 MHz (included): <-50 dBc |
| Total Harmonic Distortion |
<0.075% (10 Hz to 20 kHz, 0 dBm) |
| Spurious (non-harmonic) |
Typical (0 dBm)
≤10 MHz <-70 dBc
>10 MHz <-70 dBc + 6 dB/octave |
| Phase Noise |
Typical (0 dBm, 10 kHz offset)
10 MHz: <-125 dBc/Hz |
| Signal Characteristics |
| Square |
| Rise/Fall Time |
Typical (1 Vpp)
<10ns |
| Overshoot |
Typical (100 kHz, 1 Vpp)
≤5% |
| Duty Cycle |
0.01% to 99.99% (limited by the current frequency setting) |
| Non-symmetry |
1% of the period + 5 ns |
| Jitter (rms) |
Typical (1 Vpp)
≤5 MHz 2 ppm + 200 ps
> 5 MHz 200 ps |
| Ramp |
| Linearity |
≤1% of peak output (typical, 1 kHz, 1 VPP, 100% symmetry) |
| Symmetry |
0% to 100% |
| Pulse |
| Pulse Width |
≥16 ns (limited by the current frequency setting) |
| Rising/Falling Edge |
≥10 ns (limited by the current frequency setting and pulse width setting) |
| Overshoot |
Typical (1 Vpp) ≤5% |
| Jitter (rms) |
Typical (1 Vpp) ≥5 MHz 2 ppm + 200 ps > 5 MHz 200 ps |
| Arbitrary Waveform |
| Waveform Length |
8 pts to 2 Mpts (16 Mpts optional) |
| Vertical Resolution |
14 bits |
| Sample Rate |
200MSa/s |
| Min Rise/Fall Time |
Typical (1 Vpp)
<5 ns |
| Jitter (rms) |
Typical (1 Vpp)
≤5 MHz 2 ppm + 200 ps
> 5 MHz 200 ps |
| Editing Mode |
Point Edit, Block Edit, Insert Built-in Waveform |
| Harmonic Output |
| Harmonic Order |
≤8 |
| Harmonic Type |
Even Harmonic, Odd harmonic, Order Harmonic, User |
| Harmonic Amplitude |
The amplitude of each order of harmonic can be set |
| Harmonic Phase |
The phase of each order of harmonic can be set |
| Output Characteristics |
| Amplitude (into 50 Ω) |
| Range |
≤10 MHz: 2.5 mVpp to 10 Vpp
≤30 MHz: 2.5 mVpp to 5.0 Vpp
≤60 MHz: 2.5 mVpp to 2.5 Vpp |
| Accuracy |
Typical (1 kHz sine, 0 V offset, >10 mVpp, auto)
±1% of the setting value ±1 mV |
| Flatness |
Typical (sine, 2.5 Vpp)
≤10 MHz ±0.1 dB ≤60 MHz ±0.2 dB |
| Unit |
Vpp, Vrms, dBm |
| Resolution |
0.1mVpp or 4 digits |
| Offset (into 50 Ω) |
| Range (Peak ac+dc) |
±5 V |
| Accuracy |
1% of the setting value + 5 mV + 0.5% of the amplitude |
| Waveform Output |
| Output Impedance |
50 Ω (typical) |
| Protection |
Short-circuit protection, automatically disable the waveform output when overload occurs |
| Modulation Characteristics |
| Modulation Type |
AM, FM, PM, ASK, FSK, PSK, PWM |
| AM |
| Carrier Waveform |
Sine, Square, Ramp, Arb (except DC) |
| Source |
Internal/External |
| Modulating Waveform |
Sine, Square, Ramp, Noise, Arb |
| Modulation Depth |
0% to 120% |
| Modulating Frequency |
2 mHz to 1 MHz |
| FM |
| Carrier Waveform |
Sine, Square, Ramp, Arb (except DC) |
| Source |
Internal/External |
| Modulating Waveform |
Sine, Square, Ramp, Noise, Arb |
| Modulating Frequency |
2 mHz to 1 MHz |
| PM |
| Carrier Waveform |
Sine, Square, Ramp, Arb (except DC) |
| Source |
Internal/External |
| Modulating Waveform |
Sine, Square, Ramp, Noise, Arb |
| Modulation Depth |
0° to 360° |
| Modulating Frequency |
2 mHz to 1 MHz |
| ASK |
| Carrier Waveform |
Sine, Square, Ramp, Arb (except DC) |
| Source |
Internal/External |
| Modulating Waveform |
Square with 50% duty cycle |
| Key Frequency |
2 mHz to 1 MHz |
| FSK |
| Carrier Waveform |
Sine, Square, Ramp, Arb (except DC) |
| Source |
Internal/External |
| Modulating Waveform |
Square with 50% duty cycle |
| Key Frequency |
2 mHz to 1 MHz |
| PSK |
| Carrier Waveform |
Sine, Square, Ramp, Arb (except DC) |
| Source |
Internal/External |
| Modulating Waveform |
Square with 50% duty cycle |
| Key Frequency |
2 mHz to 1 MHz |
| PWM |
| Carrier Waveform |
Pulse |
| Source |
Internal/External |
| Modulating Waveform |
Sine, Square, Ramp, Noise, Arb |
| Width Deviation |
0% to 100% of the pulse width |
| Modulating Frequency |
2 mHz to 1 MHz |
| External Modulation Input |
| Input Range |
75 mVRMS to ±5 Vac + dc |
| Input Bandwidth |
50 kHz |
| Input Impedance |
1000Ω |
| Burst Characteristics |
| Carrier Waveform |
Sine, Square, Ramp, Pulse, Noise, Arb (except DC) |
| Carrier Frequency |
2 mHz to 30 MHz |
2 mHz to 60 MHz |
| Burst Count |
1 to 1,000,000 or Infinite |
| Start/Stop Phase |
0° to 360° |
| Internal Period |
1 µs to 500 s |
| Gated Source |
External Trigger |
| Trigger Source |
Internal, External or Manual |
| Trigger Delay |
0 ns to 100 s |
| Sweep Characteristics |
| Carrier Waveform |
Sine, Square, Ramp, Arb (except DC) |
| Type |
Linear, Log or Step |
| Direction |
Up or Down |
| Start/Stop Frequency |
The same with the upper/lower limit of the corresponding carrier frequency |
| Sweep Time |
1 ms to 500 s |
| Hold/Return Time |
0 ms to 500 s |
| Trigger Source |
Internal, External or Manual |
| Marker |
Falling edge of the sync signal (programmable) |
| Frequency Counter |
| Function |
Frequency, Period, Positive/Negative Pulse Width, Duty Cycle |
| Frequency Resolution |
7 digits/second (Gate Time = 1s) |
| Frequency Range |
1 µHz to 200 MHz |
| Period Measurement |
Measurement Range |
5ns to 16 days |
| Voltage Range and Sensitivity (non-modulating signal) |
| DC Coupling |
DC Offset Rage |
±1.5 Vdc |
| 1µHz to 100 MHz |
50 mVRMS to ±2.5 Vac + dc |
| 100 MHz to 200 MHz |
100 mVRMS to ±2.5 Vac + dc |
| AC Coupling |
1 µHz to 100 MHz |
50 mVRMS to ±2.5 Vpp |
| 100 MHz to 200 MHz |
100 mVRMS to ±2.5 Vpp |
|
| Pulse Width and Duty Cycle Measurement |
| Frequency and Amplitude Ranges |
1 µHz to 25 MHz |
50 mVRMS to ±2.5 Vac + dc |
DC Coupling |
| Pulse Width |
Min Pulse Width |
≥20 ns |
| Pulse Width Resolution |
5 ns |
| Duty Cycle |
Measurement Range (display) |
0% to 100% |
|
| Input Characteristics |
| Input Signal Range |
Brakedown Voltage |
±7Vac+dc |
Input Impedance = 1 MΩ |
| Input Adjustment |
Coupling Mode |
AC |
DC |
| High-frequency Rejection |
On: Input Bandwidth = 250 kHz;
Off: Input Bandwidth = 200 MHz |
| Input Trigger |
Trigger Level Range |
-2.5V to +2.5V |
| Trigger Sensitivity Range |
0% (about 140 mV hysteresis voltage) to 100% (about 2 mV hysteresis voltage) |
| Gate Time |
GateTime1 |
1.310ms |
| GateTime2 |
10.48ms |
| GateTime3 |
166.7ms |
| GateTime4 |
1.342s |
| GateTime5 |
10.73s |
| GataTime6 |
>10s |
|
| Trigger Characteristics |
| Trigger Input |
| Level |
TTL-compatible |
| Slope |
Rising or falling (selectable) |
| Pulse Width |
>100ns |
| Latency |
Sweep: <100 ns (typical)
Burst: <300 ns (typical) |
| Trigger Output |
| Level |
TTL-compatible |
| Pulse Width |
> 60 ns (typical) |
| Maximum Frequency |
1 MHz |
| Reference Clock |
| Phase Offset |
| Range |
0° to 360° |
| Resolution |
0.03° |
| External Reference Input |
| Lock Range |
10 MHz ± 50 Hz |
| Level |
250 mVpp to 5 Vpp |
| Lock Time |
< 2 s |
| Input Impedance (Typical) |
1 kΩ, AC coupling |
| Internal Reference Output |
| Frequency |
10 MHz ± 50 Hz |
| Level |
3.3 Vpp |
| Input Impedance (Typical) |
50 Ω, AC coupling |
| Sync Output |
| Level |
TTL-compatible |
| Impedance |
50 Ω, nominal value |
| Overvoltage Protection |
| Occurred when: |
Instrument Output Amplitude > 2Vpp or Output Offset > |2VDC| and Intput Signal > ±11.5V (<10kHz) (with ±5% error)
Instrument Output Amplitude = 2Vpp or Output Offset = |2VDC| and Intput Signal > ±3.5V (<10kHz) (with ±5% error) |
| Power Supply |
| Power Voltage |
100 V to 240 V (45 Hz to 440 Hz) |
| Power Consumption |
Lower than 40 W |
| Fuse |
250 V, T3.15 A |
| Display |
| Type |
3.5-inch TFT LCD |
| Resolution |
320 horizontal × RGB × 240 vertical resolution |
| Color |
16 M color |
| Environment |
| Temperature Range |
Operating: 0° C to 50° C
Non-operating: -40° C to 70° C |
| Cooling Method |
Fan cooling |
| Humidity Range |
Lower than 30° C : ≤95% relative humidity
30? to 40° C : ≤75% relative humidity
40? to 50° C : ≤45% relative humidity |
| Altitude |
Operating: below 3000 meters
Non-operating: below 15,000 meters |
| Mechanical |
| Dimensions (W×H×D) |
261.5 mm × 112 mm × 318.4 mm |
| Weight |
Without Package: 3.2 kg
With Package: 4.5 kg |
| Interfaces |
USB Host, USB Device, LAN |
| IP Protection |
IP2X |
| Calibration Interval |
1 year recommended calibration interval |
| Certification Information |
| EMC |
in line with EN61326-1:2006 |
|
| IEC 61000-3-2:2000 |
±4.0kV (contact discharge)
±4.0kV (air discharge) |
| IEC 61000-4-3:2002 |
3 V/m (80 MHz to 1 GHz)
3 V/m (1.4 GHz to 2 GHz)
1 V/m (2.0 GHz to 2.7 GHz) |
| IEC 61000-4-4:2004 |
1 kV power lines |
| IEC 61000-4-5:2001 |
0.5kV (Phase to Neutral)
0.5kV (Phase to PE)
1 kV (Neutral to PE) |
| IEC 61000-4-6:2003 |
3V,0.15-80MHz |
| IEC 61000-4-11:2004 |
Voltage dip:
0 % UT during half cycle
0 % UT during 1 cycle
70 % UT during 25 cycles
Short interruption:
0 % UT during 250 cycles |
| Electrical Safety |
Electrical Safety in line with
USA:UL 61010-1:2012,
Canada: CAN/CSA-C22.2 No. 61010-1-2012
EN 61010-1:2010 |
| Standard Accessories |
Power Cord
USB Cable
BNC Cable
Quick Guide
Resource CD (including User’s Guide and etc.) |
| Options |
16Mpts Memory for Arb
Rack Mount Kit (for single instrument)
Rack Mount Kit (for dual instruments)
40dB Attenuator
10W Power Amplifier
USB-GPIB Converter |