| General Specifications |
| Bar Graph Indicator (PBG8341A) |
| Construction |
Housing – nylon 6/6, window – acrylic, bezel/board supports – ABS, pins – phosphor bronze |
| Power supply |
11 – 30 Vdc |
| Signal input |
(By dipswitch configuration) Off – differential up to 5V
A – single signal (Ref. 0V) up to 5V
B – single signal (Ref. 1V) up to 6V |
| Cut out size |
45.6mm x 45.6mm |
| Fixing |
Push fit panel thickness 0.9mm to 3.2mm |
| Sealing |
Designed to IP50 standard.
(Front face may be silicon sealed after LED configuration) |
| Scale |
Supplied 0 to 100% in horizontal
Other scales, in volume, consult Parker Hannifin |
| Scaling factors |
10% to 100% range. Fully adjustable |
| Lamp intensity |
4mcd each |
| Front viewing |
Polarized |
| Weight |
29gms |
| MS150 Moisture Sensor |
| Pressure |
Maximum allowable operating pressure. (MAOP): 10bar (145 PSI) |
| Operating temperature |
| Maximum |
20°C (-4°F) |
| Flow through sesor cell |
Installed in active flowstream |
| Fluid compatibility |
Mineral oils and petroleum-based fluids |
| Viscosity Range |
Unlimited |
| Port Connection |
1/4" BSPT or 1/4" NPT/ |
| Connector Details |
M12x1 - 5 way |
| Supply Voltage |
+8 to +30Vdc |
| Sensor size/weight/material |
80mm x 43mm/0.1kg/aluminiumz |
| IP ratings |
IP68% (When mated with moulted connector1) |
| RH outputs |
(+1 to +5Vdc) or (4 to 20mA) |
| Temperature Outputs |
0 to +5 Vdc |
| MS200 Moisture Sensor |
| % Saturation Calibration Accuracy |
+3% RH |
| Temperature Calibration Accuracy |
±1°C |
| Thermal Stability |
±1% RH (over compensated temperature range +10 to +80°C) |
| Stability |
±0.2% RH typical at 50% RH in 1 year |
| Linearity |
±0.5% RH typical |
| Analog Output Hysteresis |
±0.5% RH Full Scale |
| Switched Output Hysteresis |
2% RH |
| Operating Temperature Range |
-40°F to +185°F (-40°C to +85°C) |
| Operating Humidity Range |
5 to 100% RH (non condensing) |
| Response Time |
60 sec in slow moving air at 25°C |
| Maximum Rated Pressure |
6,000 PSI (420 Bar) |
| Maximum Torque |
22 ft-lbs |
| Seal Material (depending on MS) |
Fluorocarbon, EPDM, Perfluoroelastomer |
| Material |
Stainless Steel 303 |
| Connector Details |
M12x1, 8 Way, IP67 Connector (IP68 when mated with molded cable) |
| Maximum Cable Length |
33 ft (10 m) with Voltage Output, 330 ft (100 m) with current output |
| MS300 Instrinsically Safe |
| Pressure |
| (MAOP) |
6,000 PSI (420 bar) |
| Operating temperature |
| Minimum |
-40°F (-40°C) - dependent on seal material |
| Maximum |
+185°F (+85°C) |
| Flow through sensor cell |
Installed in active flowstream |
| Fluid compatibility |
Mineral oils, petroleum-based and Phosphate esterSkydrol option available |
| Viscosity range |
Unlimited |
| Thread form connections |
See ordering information |
| Outputs |
4-20mA (current loop) |
| Calibration accuracy |
+/- 5% RH |
| Compensated thermal stability |
+/- 1% RH (+ 50°F to +176°F) |
| Materials |
Stainless steel 303 |
| Sensor size/weight |
4.21in x ø1.97in/0.66 lb (107mm x ø50mm/0.3Kg) |
| IP ratings |
IP68 (with specified molded cable) |