Voltage Set Accuracy2 |
±(0.01% of setting + 2.5 V). |
Voltage Display Accuracy |
Voltage set accuracy ±1 V, typical (±2 V, maximum). |
Current Set Accuracy5 |
±(0.01% of setting + 2.5 μA). |
Current Display Accuracy |
±1 μA, typical (±2 μA, maximum). |
Output Voltage1 |
Maximum Output Current Conditions |
Current Conditions |
50 to +5000 V DC |
5.000 mA DC |
No filter |
50 to +3000 V DC |
5.000 mA DC |
Filter 1 |
50 to +5000 V DC |
3.000 mA DC |
Filter 2 |
Voltage Resolution |
1 V (set and display). |
Voltage Limit Range |
0 to 100% full scale. |
Voltage Regulation3 |
Line: 0.001% for ±10% line voltage change.
Load: 0.005% for 100% load change, typical. |
Output Ripple (10 kHz-100 kHz)4 |
0.002% of full scale, VRMS, maximum - No filter.
1.0 mVRMS @ 1 kV - Filter 1 or Filter 2.
2.0 mVRMS @ 3 kV - Filter 1 or Filter 2.
3.0 mVRMS @ 5 kV - Filter 2. |
Rise Time (full load) 6, 7 |
1.5 seconds for 0 to within 1 V of 5000 VDC - No filter.
3 seconds for 0 to within 1 V of 3000 VDC - Filter 1.
4 seconds for 0 to within 1 V of 5000 VDC - Filter 2 |
Discharge Time (full load) 6, 7 |
1 second for 5000 VDC to 1 VDC - No filter.
3 seconds for 3000 VDC to 1 VDC - Filter 1.
4 seconds for 5000 VDC to 1 VDC - Filter 2 |
Discharge Time (no load) 6 |
<12 seconds (to <50 VDC) - No filter.
<30 seconds (to <50 VDC) - Filter 1 or Filter 2. |
Settling Time 6, 7 |
From 0 to programmed voltage; to within 99.9% of final value within 3 seconds. |
Recovery Time 6, 7 |
120 ms for 40% step change in load current (typical). |
Current Limit and Trip Range |
Voltage Range |
Filter |
0.4 mA to 5.25 mA |
0 V to 1.5 kV |
No filter or Filter 1 |
0.4 mA to 3.25 mA |
0 V to 1.5 kV |
Filter 2 |
0.5 mA to 5.25 mA |
1.5 kV to 5.0 kV |
No filter or Filter 1 |
0.4 mA to 3.25 mA |
1.5 kV to 5.0 kV |
Filter 2 |
Current Resolution |
1 μA. |
Stability |
±0.01% per hour; <0.03% per eight hours. |
Temperature Drift |
50 ppm/şC, 0ş to 40 şC, typical. |
Protection |
Arc and short circuit protected; programmable voltage and current limits and current trip. |
Output Scale |
0 to +10 V to full scale. |
Current Rating |
10 mA maximum. |
Output Impedance |
<1 Ω. |
Accuracy |
±0.2% of full scale with a 100 kΩ load, minimum. |
Update Rate |
8 Hz. |
Input Scale |
0 to +10 V for 0 to full scale. |
Input Impedance |
1 MΩ. |
Accuracy |
±0.2% of full scale. |
Update Rate |
16 Hz. |
Output Slew Rate |
<(rise time + 0.3 seconds) for 0 to full range under full load. |
Input power |
55 watts. |
2290E-5 Input Voltage |
240 V ±10%, 50 or 60 Hz. |
Rear Panel Connectors |
SHV male (Kings type 1704-1 or equivalent).
Output high-voltage connector GPIB connector.
BNC Connector (two): Voltage set/Voltage monitor; Current monitor. |
Toggle Switch |
Voltage setting or Voltage monitor. |
High-voltage Safety Interlock |
Connector: 3-pin press-in connector, 3M part number 37103-A165-00E-MB.
Pin 1: 5V out, 1.5 mA maximum out.
Pin 2: Input: High-voltage output enabled: 3-24 VDC. High-voltage output disabled: <1.2 VDC.
Pin 3: Chassis ground through a 100 Ω resistor. |
Interface Protocol |
IEEE-488.1. |
Operating Environment |
0º to 40 ºC; non-condensing. |
Dimensions |
89 mm high × 206 mm wide × 406 mm deep (3.5 in. × 8.1 in. × 16 in.). |
Weight |
5.5 kg (12 pounds). |
Safety |
Conformance to European Union low voltage directive. |
Warranty |
One year. |
Warm-up Time |
One hour. |