| Instek GSP-9300BTG Specifications |
| Frequency |
| Range |
9 kHz ~ 3 GHz |
| Resolution |
1 Hz |
| Accuracy |
±(period since last adjustment x aging rate) + stability over temperature + supply voltage stability |
| Aging Rate |
Aging Rate ± 1 ppm max |
1 year after last adjustment |
| Frequency Stability Over Temperature |
± 0.025 ppm |
0 ~ 50 °C |
| Frequency Readout Accuracy |
| Start, Stop, Center, Marker |
±(marker frequency indication x frequency reference accuracy
+ 10% x RBW + frequency resolution) |
| Trace Points |
Max. 601 points, Min. 6 points |
| Marker Frequency Counter |
| Resolution |
1 Hz, 10 Hz, 100 Hz, 1 kHz |
| Accuracy |
±(marker frequency indication X frequency reference accuracy
+ counter resolution) |
RBW/Span >=0.02 ; Mkr level to DNL>30 dB |
| Frequency Span |
| Range |
0 Hz (zero span), 100 Hz ~ 3 GHz |
| Resolution |
1 Hz |
| Accuracy |
± frequency resolution |
RBW : Auto |
| Phase Noise |
| Offset from Carrier |
|
Fc=1GHz;RBW=1kHz,VBW=10Hz;Average 40 |
| 10 kHz |
< -88 dBc/Hz |
Typical |
| 100 kHz |
< -95 dBc/Hz |
Typical |
| 1 MHz |
< -113 dBc/Hz |
Typical |
| Resolution Bandwidth (RBW) Filter |
| Filter Bandwidth |
1 Hz ~ 1 MHz in 1-3-10 sequence
200 Hz, 9 kHz, 120 kHz, 1MHz |
-3dB bandwidth
-6dB bandwidth |
| Accuracy |
± 8%, RBW = 1MHz ; ± 5%, RBW < 1MHz |
Nominal |
| Shape Factor |
< 4.5: 1 |
Normal Bandwidth ratio: -60dB:-3dB |
| Video Bandwidth (VBW) Filter |
| Filter Bandwidth |
1 Hz ~ 1 MHz in 1-3-10 sequence |
-3dB bandwidth |
| Amplitude |
| Amplitude Range |
| Measurement Range |
100 kHz ~ 1 MHz
1 MHz ~ 10 MHz
10 MHz ~ 3 GHz |
Displayed Average Noise Level(DANL)to 18 dBm
DANL to 21 dBm
DANL to 30 dBm |
| AAttenuator |
| Input Attenuator Range |
0 ~ 50 dB, in 1 dB steps |
Auto or manual setup |
| Maximum Safe Input Level |
| Average Total Power |
≤ +33 dBm |
Input attenuator ≥ 10 dB |
| 1 dB Gain Compression |
| Total Power at 1st Mixer |
> 0 dBm |
Typical ; Fc 50 MHz; preamp. off |
| Total Power at the Preamp |
> -22 dBm |
Typical ; Fc 50 MHz; preamp. on
Mixer power level (dBm) = input power (dBm) - attenuation (dB) |
| Displayed Average Noise Level (DANL) |
| Preamp off |
0 dB attenuation; RF Input is terminated with a 50 load. RBW 10 Hz; VBW 10 Hz; span 500 Hz; reference level = - 60 dBm; trace average ≥ 40 |
| 9 kHz~100 kHz |
< -93 dBm |
Nominal |
| 100 kHz~1 MHz |
< -90 dBm - 3 x (f/100 kHz) dB |
Nominal |
| 1 MHz~10 MHz |
< -122 dBm |
Nominal |
| 2.7 ~ 3.25 GHz |
< -116 dBm |
Nominal |
| Preamp on |
0 dB attenuation; RF Input is terminated with a 50 load. RBW 10 Hz; VBW 10 Hz; span 500 Hz; reference level = - 60 dBm; trace average ≥ 40 |
| 100 kHz~1 MHz |
< -108 dBm - 3 x (f/100 kHz) dB |
Nominal |
| 1 MHz~10 MHz |
< -142 dBm |
Nominal |
| 10 MHz~3.25 GHz |
< -142 dBm + 3 x (f/1 GHz) dB |
Nominal |
| Level Display Range |
| Scales |
Log, Linear |
| Units |
dBm, dBmV, dBuV, V, W |
| Marker Level Readout |
0.01 dB |
Log scale
Linear Scale |
| Level Display Modes |
Trace, Topographic, Spectrogram |
Single/Split Windows |
| Number of Traces Detector Trace Functions |
4 Positive-peak,negative-peak,sample,normal,RMS(not Video), Quasi-Peak(EMI),Average(EMI),Clear & Write,Max/Min Hold, View, Blank, Average |
| Absolute Amplitude Accuracy |
| Absolute Point |
Center=160 MHz ; RBW 10 kHz; VBW 1 kHz; span 100 kHz; log scale; 1 dB/div; peak detector; 23°C±1°C; Signal at Reference Level |
| Preamp Off |
± 0.3 dB |
Ref level 0 dBm; 10 dB RF attenuation |
| Preamp On |
± 0.4 dB |
Ref level 0 dBm; -30 dB RF attenuation |
| Frequency Response |
| Preamp Off |
Attenuation : 10 dB; Reference: 160 MHz; 20 ~ 30°C |
| 100 kHz ~ 2.0 GHz |
± 0.5 dB |
| 2GHz ~ 3 GHz |
± 0.7 dB |
| Preamp On |
Attenuation: 0 dB; Reference: 160 MHz; 20 ~ 30°C |
| 1 MHz ~ 2 GHz |
± 0.6 dB |
| 2 GHz ~ 3 GHz |
± 0.8 dB |
| Attenuation Switching Uncertainty |
| Attenuator Setting |
0 ~ 50 dB in 1 dB step |
| Uncertainty |
± 0.25 dB |
Reference : 160 MHz, 10dB attenuation |
| RBW Filter Switching Uncertainty |
| 1 Hz ~ 1 MHz |
± 0.25 dB |
Reference : 10 kHz RBW |
| Level Measurement Uncertainty |
| Overall Amplitude Accuracy |
± 1.5 dB |
20 ~ 30°C; frequency > 1 MHz; Signal input 0 ~ -50 dBm;
Reference level 0 ~ -50 dBm; Input attenuation 10 dB;
RBW 1 kHz; VBW 1 kHz; after cal; Preamp Off |
| ± 0.5 dB |
Typical |
| Spurioous Response |
| Second Harmonic Intercept |
|
Preamp off; signal input -30dBm; 0 dB attenuation |
| +35 dBm |
Typical; 10 MHz < fc < 775 MHz |
| +60 dBm |
Typical; 775 MHz fc < 1.625 GHz |
| Third-order Intercept |
|
Preamp off; signal input -30dBm; 0 dB attenuation |
| > 1dBm |
300 MHz ~ 3 GHz input -30dBm; 0 dB attenuation |
| Input Related Spurious |
< -60 dBc |
Input signal level -30 dBm, Att. Mode, Att = 0dB; 20 ~ 30ºC |
| Residual Response (Inherent) |
<-90 dBm |
Input terminated; 0 dB attenuation; Preamp off |
| Sweep |
| Sweep Time |
| Range |
204 μs ~ 1000 s
50 μs ~ 1000 s |
Span > 0 Hz
Span = 0 Hz; Min resolution = 10 μs |
| Sweep Mode |
Continuous; Single |
| Trigger Source |
Free run; Video; External |
| Trigger Slope |
Positive or negative edge |
| RF Preamplifier |
| Frequency Range |
1 MHz ~ 3 GHz |
| Gain |
18 dB |
Nominal (installed as standard) |
| Front Panel Input/Output |
| RF Input |
| Connector Type |
N-type female |
| Impedance |
50Ω |
Nominal |
| VSWR |
< 1.6 :1 |
300 kHz ~ 3 GHz ; Input attenuator ≥ 10 dB |
| RF Input |
Connector Type
Voltage/Current |
SMB male
DC +7V/500 mA max |
With short-circuit protection |
| USB Host |
Connector Type
Protocol |
A plug
Version 2.0 |
Support Full/High/Low speed |
| Micro SD Socket |
Protocol
Support Cards |
SD 1.1
Micro SD, Micro SDHC |
Up to 32GB capacity |
| Rear Panel Input/Output |
| Reference Output |
| Connector Type |
BNC female |
Nominal |
| Output Frequency |
10 MHz |
| Output Amplitude |
13.3V CMOS |
| Output Impedance |
50Ω |
| Reference Input |
| Connector Type |
BNC female |
| Input Reference Frequency |
10 MHz |
| Input Amplitude |
-5 dBm ~ +10 dBm |
| Frequency Lock Range |
Within ± 5 ppm of the input reference frequency |
| Alarm Output |
| Connector Type |
BNC female |
Open-collector |
| Alarm Output |
| Connector Type |
BNC female |
| Input Amplitude |
3.3V CMOS |
| Switch |
Auto selection by function |
| LAN TCP/IP Interface |
| Connector Type |
RJ-45 |
| Base |
10Base-T; 100Base-Tx; Auto-MDIX |
| USB Device |
| Connector Type |
B plug |
For remote control only; supports USB TMC Supports Full/High/Low speed |
| Protocol |
Version 2.0 |
| IF Output |
| Connector Type |
SMA female |
|
| Impedance |
50Ω |
Nominal |
| IF Frequency |
886 MHz |
Nominal |
| Output Level |
-25 dBm |
10 dB attenuation; RF input : 0 dBm @ 1 GHz |
| Earphone Output |
| Connector Type |
3.5mm stereo jack, wired for mono operation |
|
| Video Output |
| Connector Type |
DVI-I (integrated analog and digital), Single Link. Compatible with VGA or HDMI standard through adapter |
| RS-232C Interface |
| Connector Type |
D-sub 9-pin female |
Tx , Rx , RTS , CTS |
| GPIB Interface (Optional) |
| Connector Type |
IEEE-488 bus connector |
|
| AC Power Input |
| Power Source |
AC 100 V ~ 240 V, 50/60 Hz |
Auto range selection |
| Battery Pack (Optional) |
| Battery Pack |
6 cells, Li-Ion rechargeable, 3S2P |
With UN38.3 Certification |
| Voltage |
DC 10.8 V |
| Capacity |
5200 mAh/56Wh |
| General |
| Internal Data Storage |
16 MB nominal |
|
| Power Consumption |
< 65 W |
|
| Warm-up Time |
< 30 minutes |
|
| Temperature Range |
+5 °C ~ + 45 °C
-20 °C ~ + 70 °C |
Operating
Storage |
| Dimensions & Weight |
50(W) x 210(H) x 100(D) mm, Approx. 4.5kg
13.8(W) x 8.3(H) x 3.9(D) inch, Approx. 9.9lb |
Inc. all options (Basic + TG + GPIB + Battery) |
| Tracking Generator |
| Frequency Range |
100 kHz ~ 3 GHz |
|
| Output Power |
-50 dBm ~ 0 dBm in 0.5 dB steps |
|
| Connector Type |
N-type female |
50Ω Nominal |
| Output VSWR |
< 1.6 : 1 |
300 kHz ~ 3 GHz, source attenuation 12 dB |