Recommend to a Friend
Hakko 633-01 Iron Holder
3.0
Bought to hold Hakko FR 301 de-soldering tool. The holder works ok with the tool. It would be helpful if it had more weight to it to keep from sliding around when removing the tool and putting it back in place, and especially when using tip cleaning pod. As it is you have to use the other hand to hold it in place. Will look for some way to fasten it to the bench, but would really like to be able to move it from place to place.
Jim Heinzel on
Sep 13, 2022
Recommend to a Friend
Perfect Complement to Desoldering Tool
5.0
When I bought the FR-301 desoldering tool, I decided to bite the bullet and buy the stand to go with it. It works great and it is nice to have the tip cleaner right there where you need it. It is a luxury, but it makes the whole thing easier to use.
FRED TRAVERS on
Sep 29, 2020
Recommend to a Friend
Hakko Products - GOOD STUFF!
5.0
Simple and effective. I purchased this for Hakko FR301 Desoldering tool, but it would work for the majority of soldering irons. The Tip Cleaner works well and is easy to clean.
on
Sep 28, 2020
Recommend to a Friend
Very Useful Holder for Hakko FR-301 TOOL
5.0
This is a good inexpensive holder the Hakko FR-301 TOOL that comes with a tip cleaner : )
Verified Purchase
Allan Trias on
Jul 24, 2020
Recommend to a Friend
Strong and durable
5.0
Bought this for the Hakko FR-301. I was a little worried about the fit but it holds it well and keeps it clean.
Verified Purchase
Kirk on
Jul 16, 2020
Recommend to a Friend
Hakko Iron Holder
5.0
Great accessory to have on a cluttered workspace!
on
Jul 05, 2020
Recommend to a Friend
Sturdy
4.0
Holds the FR-301 solid, no problem.
on
Jun 22, 2020
Recommend to a Friend
Hakko 633-01
5.0
This holder exceed my expectation. After a long while browsing the internet for a holder that would last much longer than a typical clone soldering iron holder from Asia, I have found Hakko 633-01. I was quite reluctant at first, but decided to go ahead with the order. I don't regret making such a decision. Ideally this holder would be a good companion for another Hakko soldering iron. It works very well with other brands as well. I just wish that the holder is not moving as much while placing on a smooth surface. If you are using an SMD anti-static mat, this should not be a concern at all.
I highly recommend this product.
Verified Purchase
Andrew on
Jun 04, 2020
Recommend to a Friend
Hakko Holder
4.0
I would definitely get this if you have the 309 gun, It holds it well. I'm not too crazy about the wire mesh cleaner though, I really don't think it's stiff enough to clean the 309 gun.
Anonymous on
May 28, 2020
Recommend to a Friend
A must have
5.0
This is a must have for the Hakko FR-301! Super solid!! I wish it came in the box with the FR-301 to begin with...
Verified Purchase
Anonymous on
Apr 30, 2020
Recommend to a Friend
Bought as replacement/upgrade
5.0
Bought this to replace an old unknown stand. What a difference!! Iron is held much more securely. Definitely worth purchasing
Kyle Majikas on
Aug 16, 2019
Recommend to a Friend
Hakko 633-01 iron holder with 599B Tip Cleaner
5.0
This iron holder works perfectly on my work bench, well made and should last a long time!
on
Apr 18, 2019
Recommend to a Friend
The best holder I have ever used
5.0
The holder has a heavy base which withstands most of my irons I have and simply the best iron holder I have ever used. Option of tip cleaner sponge is a nice addon.
Verified Purchase
Anonymous on
Apr 12, 2019
Recommend to a Friend
A Benchmark
5.0
This tool simply gets the job done quickly and easily. Maintenance is a piece of cake. It's difficult to imagine life without this tool. Many of my friends continue to use their little manual vacuum suckers and fluxed braid, but after seeing this at work for a minute or two they put it on their list of tools to lust after. Assuming the new FR-301 matches this unit the $50 reduction in price would make it a no-brainer for somebody who doesn't want to waste their life unsoldering.
Verified Purchase
Peter Soper on
Apr 24, 2018
Recommend to a Friend
Works exactly as advertised
5.0
After using about all alternatives, I finally broke down & bought this ‘real’ tool. Couldn’t be happier...wish I had done that sooner.
Gfkdrob on
Apr 01, 2018
Recommend to a Friend
great stand
5.0
I'm really happy with the stand. It takes up little space on my overcrowded workstation. The rubber feet on the bottom hold the stand from sliding around when your cleaning your tip.
nackesww on
Mar 02, 2018
Recommend to a Friend
A life saver for repairs...
5.0
This Hakko FR300 has surpassed my expectations. A few minutes after opening it for the first time, I had pulled multiple 8 pin relays from a board I was working on.
The selection of tips is important, in my opinion. Having a tip that is wide enough for your pins (>1mm for older things) is a must have.
Verified Purchase
Jason Ledbetter on
Feb 27, 2018
Recommend to a Friend
hakko fr300
5.0
works very well . Good suction ,easy to clean.
paul on
Feb 25, 2018
Recommend to a Friend
Works great...
5.0
I used the FR-300 last night for the first time and it worked great. I had some bad video DRAM's on a vintage video card. The FR-300 made quick work of removing them without damaging the PCB and I installed some new sockets and new DRAM and all works well again.
Verified Purchase
Anonymous on
Feb 15, 2018
Recommend to a Friend
Best desoldering tool!
5.0
Do yourself a favor, and skip the cheap crap on Ebay...you get what you pay for. I have tried three tools, and this is the LAST tool I will get for desoldering. It works Awesome! very fast heatup, and very fast cleanup after a desoldering job. Really does a good job from larger boards, down to smaller boards....very fast, very clean....Worth EVERY PENNY!!
cyborgCNC on
Feb 15, 2018
Recommend to a Friend
Good product
4.0
This is a great product with some minor issues.
First, the good. It is sturdy, well constructed with thick steel sheet. The plastic holder (the black round ring at the top) for the iron resists the heat and hasn’t deformed or become damaged due to my clumsy location of the iron in the holder. Finally, it doesn’t tip over. During usage.
Now, the minor issues. The hole where the sponge holder fits is a bit larger than the brass sponge holder; this causes the sponge holder to slid out of the iron holder during transport, and it can become inconvenient during usage due to loosen sponge holder. Can be solved with some tape though. Finally, the base has 4 anti sliding feet, but the iron holder itself is quite light and slides away from position on some occasions. I think this will vary depending on the surface of your workbench; mine is moderately slippery.
BFelectronics on
Jan 05, 2018
Recommend to a Friend
Works Great
5.0
This desoldering gun is a big time saver and works great. I also give TEquipment 5 stars, as they had excellent phone customer service and got the order shipped out right away.
Verified Purchase
David on
Dec 15, 2017
Recommend to a Friend
FR-300 works great!
5.0
Works great! Fast, fast, fast! Easy to clean and really good suction. Took components off of an old DSL modem and other old boards, didn't take long at all. So much better than a suction desoldering tube. Makes desoldering through-hole components so easy. I'll never go back to solder wick, squeeze bulb suction, etc. This thing has already paid for itself in reclaimed parts and time saved.
Verified Purchase
Chris F. on
Nov 08, 2017
Recommend to a Friend
You need a stand for the FR-300
5.0
This stand gets the job done for preventing your Hakko FR-300 from burning or melting anything it might come into contact with while idling on your bench. The integrated tip cleaner is a nice touch, although I wish it fit a little more snugly (it tends to spin around a bit). I got mine as part of the full kit for the FR-300, and I'm glad I have it.
Verified Purchase
Frank Moscowitz on
Jun 02, 2017
Recommend to a Friend
What did I ever do without this tool?
5.0
I've been repairing audio related electronics for 10 years, and up until recently had always gotten by with the solder wick and manual solder vacuum pump for my desoldering needs. With a couple of big recapping jobs on the horizon I ordered the Hakko FR-300, and HOLY COW am I glad I did. This tool is an absolute must for any high volume desoldering work. It saves time AND effort, and I haven't lifted a trace since I started using it. Cleaning is super easy, the included cleaning tools get the job done quickly. Do yourself a favor and get the full kit with the stand and extra tips. Worth it!
Verified Purchase
Frank Moscowitz on
Jun 02, 2017
Recommend to a Friend
Desoldering-Pins Antique Radios
5.0
Works great for desoldering tube socket pins on antique radio. Often the solder is heavy on these pins so it saves a lot of tedious work with solder wick.
R.Brown on
May 19, 2017
Recommend to a Friend
perfect
5.0
works perfect .. nice piece of equipment
miguel on
May 13, 2017
Recommend to a Friend
Hakko FR-300
5.0
This tool works great.. But I would strongly suggest ordering the different size tips to go along with de-soldering tool.
Verified Purchase
Bob CEC on
Apr 09, 2017
Recommend to a Friend
Works
5.0
Other stands might work better or might be cheaper, but I went with the Hakko FR-300 bundle so I effectively got this stand for free. Gets the job done.
Verified Purchase
Anonymous on
Jan 06, 2017
Recommend to a Friend
Essential
5.0
This is a must have for anyone doing even just light rework. Works as advertised, and has the same high quality I expect from Hakko-made tools.
Verified Purchase
Anonymous on
Jan 06, 2017
Recommend to a Friend
Hakko FR-300 Love it!
5.0
This has made troubleshooting electronics faster for me. Now when I need to desolder one lead of a component to test, no problem. Fire up the Hakko and go to work. Buy the other nozzle sizes. Having the right size nozzle on it makes a difference. Money well spent.
Gregg on
Sep 30, 2016
Recommend to a Friend
Great field and bench tool
5.0
What can I say with a little practice and learn curve this one has it for portable use
I would recommend getting the larger tip and another size to your own needs had to remove some transformers and heat sinks from double side threw holes other components was a snap. A little trick with heat sinked transistors on center lead I found putting a little dab of flux on the side of a board at the contact point wait for a little cloud of vapor then push the switch made it faster and cleaned nicely with out having any retry's.
Detimothy on
Sep 20, 2016
Recommend to a Friend
Holder works
5.0
Using it on the desoldering tool works fine and some times I will grab another soldering iron of another bran and find them to fit as well.
pleased with equipment net
Detimothy on
Sep 20, 2016
Recommend to a Friend
Stop wasting your time, and just buy it!
5.0
If you do ANY rework at all, you need this tool. Even at home. I've used hollow-tip solder suckers in work environments but never figured it was worth having one at home. But I finally got tired of poor performance from the old manual spring-based units and took the chance on this one. WOW... I wish I could recover all the time (and destroyed PCB's!) that I wasted by not buying this sooner.
Seriously - spend the money. You'll thank me.
Verified Purchase
RICHARD HARTMAN on
Aug 01, 2016
Recommend to a Friend
Awesome. Goodbye, spring-loaded solder sucker!
5.0
These seem expensive for what they do. I've used them in the past and sure, they're great, but hey - why not just get by with a $10 spring loaded solder sucker?
Answer: Because this unit SUCKS! And that's a GOOD thing! There is no substitute for clearing PCB through-holes; you can flail around with the old spring suckers and waste lots of time and risk damaging the board, or you can grab one of these units and do a far better job in far less time.
Seriously... if you do much rework at all, stop thinking about it and just spend the money. It will be worth it the very first time you use it.
IDEngineer on
Jul 23, 2016
Recommend to a Friend
Simple but effective
5.0
Came as a bundle with the Hakko FR-300 vacuum desolder gun. Something of a generic soldering iron stand; could be a bit taller to better fit the FR-300, but still works quite well. Allows my FR-300 to remain on the bench full time instead of living in its carry case.
IDEngineer on
Jul 23, 2016
Recommend to a Friend
Great Product!
5.0
I had an old Tenma product before and this blows that machine out of the water. It heats up very quickly as does a great job of sucking solder out of boards. I replaced over 20 capacitors on a few TVs, this product made it very easy.
Verified Purchase
Christopher Blatt on
Jul 07, 2016
Recommend to a Friend
Typical Hakko
5.0
Very nice product which is usually the case with Hakko.
Super clean removal of solder with the correct nozzle.
Its calling you...you know you want it.
Verified Purchase
FP on
Apr 11, 2016
Recommend to a Friend
Great item
5.0
If you own a Hakko 808 then this is mandatory. I recommend this as a professional with 4 808's
Acorn amplifiers on
Mar 26, 2016
Recommend to a Friend
Great desoldering tool
5.0
I've used an older 808, and the FR300 is definitely better. It's lighter, has better balance, and is easier to operate overall. The 300 has an on-off switch and a temperature control that is simple to use, making it a bit nicer than the 808. My only complaint is that the nozzles can get clogged, not from solder, but from caked or charred flux, so make sure to use the clearing pin to remove this as you go. Still, if you keep the tip tinned and adjust the heat properly, it does an excellent job with both through hole and SMD PCBs. I do less and less through hole work, but it's still invaluable for cleaning a surface mount pad. It's far more gentle and fast than solder wick or a manual solder pump. Highly recommended if you do any rework or repair at all.
Verified Purchase
Monte McGuire on
Mar 20, 2016
Recommend to a Friend
It really sucks!
5.0
Things really sucks! It sucks the old solder from a double sided circuit board, and makes replacement of failed components such an easy task that I am unsure how I lived without one. Is it expensive? Yes. Is it worth it? Absolutely! Are there other ways to remove thru hole devices? Sure, but it’s harder and there is a much higher risk of damage to the circuit board. The Hakko FR-300 heats up fast, is easy to clean, and comfortable to use. I have used the manual solder suckers, solder wick, and a Pace vacuum de-solder pencil in the past and the Hakko outshines these hands down.
The best part is how fast it heats up. I don’t have to leave it turned on unless I am doing a large amount of rework. It heats up within 20-30 seconds and just plain works.
I have even used it on antique radios where the large components and terminal lugs contain a large quantity of solder. It just takes a little extra attention to make sure the solder goes thru the heating element and into the holding tank. There is a risk of plugging it up, but it’s been easy to clean thus far. I am thinking about getting a larger tip for this use as I am using the tip that was included.
Overall I am very pleased with my purchase and of course Tequipment.net is THE place to buy from. Fast shipping and you can be sure that what you get is not a knock-off from eBay.
Eric on
Feb 23, 2016
Recommend to a Friend
manger
5.0
That 's the best one found.
ling on
Jan 18, 2016
Recommend to a Friend
Hakko is good stuff
5.0
Bought to upgrade from the Weller sponge type iron holder.
The Hakko has lots of nice little touches, like rubber feet so it doesn't slide around, lots of storage for extra tips and of course the metal type tip cleaner which is vastly better than the wet sponge type, for not cooling the tip and not oxidizing what solder is on the tip.
Verified Purchase
Jeff Weaver on
Jan 13, 2016
Recommend to a Friend
Great tool for rework!
5.0
Hakko 300 is an excellent tool (de-soldering station) for reworking older DIP - through hole based stereo equipment from 70's and 80's. Hakko is well balanced and easy to operate in tight quarters. After using it for about 4 weeks I only had to clean tip couple of times. Highly recommended for professional or serious DIY rework - you can forget about using your hand operated solder pump after using it.
RFmaster on
Nov 26, 2015
Recommend to a Friend
Wow, What a Great Tool
5.0
Our first move up from a spring loaded solder sucker...Liked it so much we ordered a second one! Perfect for removing parts without damage to the board or the part. Great heat capacity and plenty of suction. Very comfortable and easy to use. Not so good if you cut the legs off the part and then try to remove the remaining wire from the hole
Steve on
Oct 28, 2015
Recommend to a Friend
Great Holder! Works well with the FR-300
5.0
Bought this holder to use with the FR-300...Quality construction, strong but still light weight. Would work with almost any iron
Steve on
Oct 28, 2015
Recommend to a Friend
Fr 300
5.0
Now that I have the FR 300 my restoration of old radios going much faster, I can take on any job knowing my de-soldering will be much easier!
Bruce on
Oct 22, 2015
Recommend to a Friend
hakko-fr300
5.0
Excellent product and service
Verified Purchase
Anonymous on
Aug 12, 2015
Recommend to a Friend
Hakko FR-300 works great so far
5.0
I've had this for about a month now, and so far I love it. Seems to suck just as well as the $900 Pace system I've got in the shop, and this is a lot more convenient to take on the road. Yeah, it's a little heavier than the Pace handpiece, but it's well balanced, and easy to hold. I haven't had it long enough to comment on durability or ease of maintenance.
John Chester on
Jul 10, 2015
Recommend to a Friend
A nice tool!
5.0
This is my first vacuum desoldering tool, other than a manual Soldapult, but I've used a Hakko 808 before, and the FR-300 is definitely nicer. It seems lighter and better balanced than an 808, so it's easier to position accurately on a delicate board. The vacuum trigger switch is also in a better spot, so it doesn't 'go off' accidentally quite as easily.
It has an easy to adjust power level control, as well as a power on / off switch. Unlike the 808, you can easily turn the tool off after one use, saving the nozzle from becoming excessively un-tinned / needing to be re-tinned. It powers up fairly quickly as well, so unless one's desoldering a number of connections, there's no reason why it shouldn't be powered off after each use.
I managed to clog the nozzle with one strand of exactly the wrong gauge of wire, but once I realized that I could turn the temperature up and add fresh solder/flux to the nozzle, it was easy to clear with the vacuum. Emptying the chamber is fairly pleasant too - the removed solder tends to aggregate into a nice, solid blob, and not a pile of extremely fine powdered metal, making it much easier to transfer to my hazmat jar.
Overall, it's a really nice tool, useful for rework of ancient through hole boards that used questionable adhesives, as well as modern SMD rework where it does a great job leveling a pad with minimal damage and effort. Highly recommended!
Verified Purchase
Monte McGuire on
Jul 06, 2015
Recommend to a Friend
Hakko FR-300 Handheld Desoldering Tool
5.0
I received the Hakko FR-300 super quick after ordering so that was a big plus. The other big plus was how great and easy to use the Hakko was. It made desoldering seem like fun instead of a chore. It's a lot quicker/efficient than using a sucker or wick. Love it!! Should have bought one sooner.
Verified Purchase
Gregory Raft on
May 18, 2015
Recommend to a Friend
HAKKO FR-300
5.0
The Hakko FR-300 is a breeze to use. It works like specified and is a joy to use. It actually makes turns what can be a task into a pleasurable experience. Sure you can use a wick or a sucker, but after to try this method, you'll be hooked.
graftdesign on
May 18, 2015
Recommend to a Friend
Great product!
5.0
We have a Hakko 808 at work, the model this replaced, so I was pretty familiar with the quality and function. The FR-300 is much improved with a longer power cord, an on/off switch, and a temp setting that's much easier to use than the recessed trim pot on the 808. I frequently salvage through-hole parts from old devices and the FR-300 makes it quick and easy.
Verified Purchase
Jim Titus on
May 15, 2015
Recommend to a Friend
Required for every Maker's workbench
5.0
A friend and many fellow pinball collectors raved online about the Hakko-808 desoldering tool, but lamented it no longer being available. I must say that the FR-300 is a worthy next generation replacement. I now understand why people worship their Hakko tools.
This makes desoldering a breeze, and should be a part of every tinkerer's toolbox. Quickly preheat the tool, apply the tip to your component lead, and give a quick blast to the vacuum. It leaves the board and component solder-free with minimal effort.
Anonymous on
Apr 26, 2015
Recommend to a Friend
HAKKO FR300
5.0
I got the tool, the FR300 and used it. It sure makes desoldering a fast and efficient way to go. I recommend this fine product to those looking for this type tool.
Ted Walker on
Apr 21, 2015
Recommend to a Friend
HAKKO FR-300 Desoldering Tool
5.0
If you've never used one of these, you need one. If you've used a previous version of HAKKO desoldering tool, you need to put it in the drawer as a spare and get the new one FR-300. Everything has been improved, it works and cleans up like a dream. Start up in seconds, and power (tool) save feature when idle. Every part of this version has been changed for the better, all the bad is gone now. BUY IT!
Larry on
Apr 20, 2015
Recommend to a Friend
Good product
5.0
Good product - does what it is supposed to do.
Quite helpful for removing components from boards with ease compared to traditional methods.
I'd tried without success removing components with large number of connections and this unit made child's play of it.
I can also state that initial unit had a problem which was handled quickly and very professionally by Hakko.
I will use Hakko tools again and TEquipment because they both can be depended upon and are there to support you.
ace on
Apr 19, 2015
Recommend to a Friend
Hakko solder sucker
5.0
Product works very well. Need option for larger nozzle. Good buying experience with the distributor.
stevew on
Apr 15, 2015
Recommend to a Friend
Great Desolder unit
5.0
Just what I have been waiting for. Saved me on many jobs. As long as you clean it after each job as it explains it then works flawlessly. Highly recommended.
Gary on
Apr 11, 2015
Recommend to a Friend
Pricey but ever so satisfying!!!!
5.0
I Love grabbing this tool. It's quality in your grip - heats up really fast, so fast that when I turn it on I don't set it down to heat up I just hold it for about 20 seconds and its nice and hot already. something I'll be keeping hopefully forever!
Anthony on
Apr 11, 2015
Recommend to a Friend
FR-300 vs. 808
5.0
The FR-300 is definitely a step up over the 808 for air suction, heat transfer and easier cleaning. Another very important improvement over the 808 is the temperature dial which isn't prone to damage like the 808's temperature trimpot.
The handle design is quite different than the 808, if you're used to it you'll need a few days to fully adjust to the FR-300; but once you do I feel it's a lot better. If you didn't like the 808's handle design in the first place then the FR-300 will feel better instantaneously.
The only strange caveat to using the FR-300 is that I always have to put flux on the cleaning rod in order for it to successfully go through the nozzle. On the plus side, it is possible to fix clogged tips on the FR-300 by putting flux inside the tip (screwing it back in), setting the heat to max, and then also coating the cleaning rod in flux. The 808's clogged tips were virtually impossible.
Definitely get the FR-300 if you want better *performance* for difficult through-hole multilayer boards or the like. The FR-300 also seems to keep its performance consistently whereas the 808 would lose suction over time.
D. R. on
Apr 11, 2015
Recommend to a Friend
Hakko FR-300
4.0
The desoldering tool does a good job. I have been using it for a year and I am pleased with it's performance. The only issue I had was the nozzle got clogged but using a small drill solved the problem. If this one ever breaks I will purchase another one.
BWheat on
Apr 09, 2015
Recommend to a Friend
FR-300
4.0
GREAT GUN. THE ONLY NEGATIVE IS THE LACK OF A STAND.
TODD GILL on
Apr 03, 2015
Recommend to a Friend
Hakko FR 300
4.0
Great product so far. Shipping was a little crazy. Received different parts at different times
Stan on
Apr 02, 2015
Recommend to a Friend
Excellent Product
5.0
I bought this to reclaim parts off of old boards for recycling. This thing is amazing. It heats up fast and removes solder fast. Just make sure to get several various tip sizes because the one it comes with is too small for larger components.
Taco on
Apr 01, 2015
Recommend to a Friend
Excellent way to desolder without destroying thing
5.0
Wow, I can't believe I've waited all this time to buy one. This makes removing components extremely fast and easy. I don't ruin pads or traces anymore. Love this, definitely don't cheap out and get a knockoff, the Hakko is the real deal.
Verified Purchase
Aaron Morris on
Mar 17, 2015
Recommend to a Friend
Better than before
5.0
I used to work with the preview version of this pistol. It was very useful already. But now with the new improvements such as better control of the temperature, the option to turn on and off the equipment and the redesign of the way we remove the noozle, altogether in a case made the product almost perfect. It worths to have it!
Verified Purchase
Rodrigo Baleiro on
Mar 11, 2015
Recommend to a Friend
Easy
5.0
Easy order, great price, no issues. Love the free cleaner we got too!
Verified Purchase
Deanna Ossenkop on
Jan 23, 2015
Recommend to a Friend
Desoldering tool
5.0
The tool that I received for my Dad was a piece that had been used and then returned. There was pieces broken. I called Tequpment and they sent a return number and after about a month I finally received the new tool directly from the manufacturer. I am glad that I received a new tool. My dad says that it works like it is supposed to.
Shannon on
Jan 20, 2015
Recommend to a Friend
Makes PCB Rework Easy
5.0
Have previously used solder suckers braid a lot. Had used a 808 device and found it quite good, so decided to pick up this.
Works amazingly well - heats up in a few seconds, which is handy. Carrying case is nice & has a heat shield so you can put away hot. Easy to clean out the canister, very well-thought out design.
Made a quick video review here: http://youtu.be/oxf0a9JKo7U
And here's an example of desoldering a 30-pin header: http://youtu.be/gZxqpH23ZEM
coflynn on
Sep 05, 2014
Recommend to a Friend
Easy & Effective
5.0
The Hakko FR-300 desoldering gun is very easy to use straight out of the box and very effective. I had my bad relay off the board in a minute where other methods (sucker/braid) had failed to get it off.
Verified Purchase
Anonymous on
Aug 22, 2014
Recommend to a Friend
Hakko Desoldering Gun
5.0
I replaced an older Ungar desoldering station that used a separate pump and hand tool. I find the Hakko much easier to use and certainly a lot easier to empty solder collector.
Verified Purchase
William Schrader on
Jul 29, 2014
Recommend to a Friend
Great Product and Good Service
5.0
The Hakko FR-300 does a fantastic job removing solder. The handle is very comfortable and it heats up quickly. Typically I have purchased $20-$30 desoldering tools not wanting to spend money on a quality tool. After being frustrated for years I decided to try the Hakko. I have a Hakko soldering station which I also love. Both tools are the best investment I have made that save time and perform flawlessly day after day. Tequipment also delivered the product quickly. This is my first buying experience with Tequipment and it definitely will not be my last.
RocketMan on
Jul 25, 2014
Recommend to a Friend
Hakko FR-300 First Impressions
5.0
I'm very happy with the changes made to the new Hakko FR-300 compared to the older Hakko 808 desoldering gun. Standout improvements are the sleeker and smaller design and better ergonomic and relaxed fit in the hand. The handle and trigger mechanism is now designed to make prolonged use of the gun much more comfortable. The on-off switch with LED indicator and longer cord is another BIG improvement over the 808. I like the thumb wheel temperature selector with the visual reference to temperature settings, it’s way easier to adjust than the 808. Tip retainer mechanism on the FR-300 is much improved as is the solder tube and holder. While the slight increase in vacuum suction is welcome, the decrease in size of the gun made mostly possible by going to a single diaphragm pump is a big design plus. An increase in wattage should positively round off the numerous improvements to an already good product, making the FR-300 a must have on the electronics workbench.
Some small CONS: There is no protective iron cover included in the FR-300 kit as was included in the 808 kit. The protective tube that is used to protect the case from a hot iron is a poor afterthought and a next to useless. Fewer filter parts are included with the newer kit, compared with the older kit. Although Hakko put an LED on the front of the handle that lights when the heater element is on, it is difficult to see and of course the light is intermittent, lighting only when the gun is actually heating the element. It would have been nice if an additional LED be installed near the on/off switch, indicating an ON condition and in a place viewable while in a solder station holder. The LED installed in the front of the handle is not viewable in the guns normal safe storage position, which should be located in a proper holder somewhere on the workbench.
Overall: A BIG Thumbs Up for the new Hakko FR-300. While I have not had a chance to use it yet, my first impressions are, I like it!
Verified Purchase
iRad on
May 09, 2014
Recommend to a Friend
Hakko FR 300 First Impressions
5.0
I'm very happy with the changes made to the new Hakko FR-300 compared to the older Hakko 808 desoldering gun. Standout improvements are the sleeker and smaller design and better ergonomic and relaxed fit in the hand. The handle and trigger mechanism is now designed to make prolonged use of the gun much more comfortable. The on-off switch with LED indicator and longer cord is another BIG improvement over the 808. I like the thumb wheel temperature selector with the visual reference to temperature settings, it’s way easier to adjust than the 808. Tip retainer mechanism on the FR-300 is much improved as is the solder tube and holder. While the slight increase in vacuum suction is welcome, the decrease in size of the gun made mostly possible by going to a single diaphragm pump is a big design plus. An increase in wattage should positively round off the numerous improvements to an already good product, making the FR-300 a must have on the electronics workbench.
Some small CONS: There is no protective iron cover included in the FR-300 kit as was included in the 808 kit. The protective tube that is used to protect the case from a hot iron is a poor afterthought and a next to useless. Fewer filter parts are included with the newer kit, compared with the older kit.
Overall: A BIG Thumbs Up for the new Hakko FR-300. While I have not had a chance to use it yet, my first impressions are, I like it!
iRad on
May 09, 2014
No reviews found to display for this rating.