| Power supply |
| Voltage range |
100 V to 500 V using safety plug input when powering from the measurement circuit |
| 100 V to 240 V MA-C8 and using standard power cord (IEC 60320 C7) |
| Power consumption |
Maximum 50 VA (max. 15 VA when powered using MA-C8 adapter) |
| Efficiency |
≥ 68.2 % (in accordance with energy efficiency regulations) |
| Maximum no-load consumption |
< 0.3 W only when powered using IEC 60320 input |
| Mains power frequency |
50/60 Hz ± 15 % |
| Battery |
Li-ion 3.7 V, 9.2 Wh, customer-replaceable |
| On-battery runtime |
Typically 4 hours |
| Charging time |
< 6 hours |
| Data acquisition |
| Resolution |
16-bit synchronous sampling |
| Sampling frequency |
10.24 kHz at 50/60 Hz, synchronized to mains frequency |
| Input signal frequency |
50/60 Hz (42.5 to 69 Hz) |
| Circuit types |
1-φ, 1-φ IT, split phase, 3-φ delta, 3-φ wye, 3-φ wye IT, 3-φ wye balanced, 3-φ Aron/Blondel (2-element delta), 3-φ delta open leg, currents only (load studies) |
| Data storage |
Internal flash memory (not user replaceable) |
| Memory size |
Typical 20 logging sessions of 4 weeks with 1-minute intervals and 500 events |
| Basic interval |
| Measured parameters |
Voltage, current, aux, frequency, THD V, THD A, power, power factor, fundamental power, DPF, energy |
| Averaging interval |
User selectable: 1 sec, 5 sec, 10 sec, 30 sec, 1 min, 5 min, 10 min, 15 min, 30 min |
| Averaging time min/max values |
Voltage, current: Full cycle RMS updated every half cycle (URMS1/2 according to IEC 61000-4-30 Aux, Power: 200 ms) |
| Demand interval (Energy Meter Mode) |
| Measured parameters |
Energy (Wh, varh, VAh), PF, maximum demand, cost of energy |
| Interval |
User selectable: 5 min, 10 min, 15 min, 20 min, 30 min, off |
| Power quality measurements |
| Measured parameter |
Voltage, frequency, unbalance, voltage harmonics, THD V, current, harmonics, THD A, TDD, voltage interharmonics, TID V, current interharmonics, TID A, Flicker, Mains Signaling, under/over deviation |
| Averaging interval |
10 min for all parameters
2 hrs (long term Flicker PLT)
150/180 cycles (3 s) for harmonics (requires software license IEEE519/REPORT) |
| Individual harmonics |
2nd to 50th harmonic
Grouping according to IEC 61000-4-7 user configurable depending on application:
Sub-grouped (harmonics + interharmonics), grouped or harmonic bins only |
| Interharmonics |
1st to the 50th interharmonic |
| Total harmonic distortion |
Calculated on 50 voltage harmonics |
| Events |
Voltage: dips, swells, interruptions, current: inrush current
1748: mains signaling, transients (low frequency) |
| Triggered recordings |
RMS profile: Full cycle RMS updated every half cycle of voltage and current up to 11 s
(URMS1/2 according to IEC 61000-4-30)
Waveform of voltage and current up to 200 ms, 10/12 cycles
Mains signaling: 10/12 cycle RMS recording of the configured frequencies up to 120s |
| Inrush |
RMS profile based on 1/2 cycle RMS steady state triggering |
| Flicker |
In accordance with IEC 61000-4-15 and IEEE 1453 |
| Mains signaling |
Two user defined frequencies up to 3 kHz |
| PQ Health |
Summarizes power quality measurements in one table. Detailed data available for each parameter |
| EN 50160 |
Compliance with standard |
| Programmable PQ limits |
Enables user defined limits for local standards compliance |
| Standards compliance |
| Harmonics |
IEC 61000-4-7: Class 1 |
| IEEE 519 (short time and very short time harmonics) |
| Power quality |
IEC 61000-4-30 Class A, IEC 62586-1, IEC 62586-2 (PQI-A-PI device) |
| Power |
IEEE 1459 |
| Power quality compliance |
EN 50160 |
| Safety |
General: IEC 61010-1: Pollution Degree 2
Measurement: IEC 61010-2-033: CAT IV 600 V / CAT III 1000 V
Power Supply: Overvoltage Category IV, Pollution Degree 2
Li-ion Battery: IEC 62133 |
| USB-A |
File transfer via USB flash drive, firmware updates, max. supply current: 120 mA |
| WiFi |
File transfer and remote control via direct connection or WiFi infrastructure |
| Bluetooth |
Read auxiliary measurement data from Fluke Connect ® 3000 series modules
(requires supported USB to BLE or WiFi/BLE adapter, check for availability) |
| USB-mini-B |
Data download device to PC |
| Voltage inputs |
| Number of inputs |
4 (3 phases referenced to neutral) |
| Maximum input voltage |
1000 Vrms, CF 1.7 |
| Input impedance |
10 MΩ |
| Bandwidth |
42.5 Hz to 3.5 kHz |
| Scaling |
1:1 and variable |
| Measurement category |
1000 V CAT III/600 V CAT IV |
| Current inputs |
| Number of inputs |
4 (3 phases and neutral), mode selected automatically for attached sensor |
| Input voltage |
Clamp input: 500 mVrms/50 mVrms; CF 2.8
Rogowski coil input: 150 mVrms/15 mVrms at 50 Hz, 180 mVrms/18 mVrms at 60 Hz; CF 4 all at nominal probe range |
| Range |
1 A to 150 A/10 A to 1500 A with thin flexible current probe i17XX-flex1500 IP 24"
3 A to 300 A/30 A to 3000 A with thin flexible current probe i17XX-flex3000 IP 24"
6 A to 600 A/60 A to 6000 A with thin flexible current probe i17XX-flex6000 IP 36"
40 mA to 4 A/0.4 A to 40 A with 40 A clamp i40s-EL |
| Bandwidth |
42.5 Hz to 3.5 kHz |
| Scaling |
1:1 and variable |
| Auxiliary inputs |
| Number of inputs |
2 (Analog with auxiliary adapter, or up to 2 BLE devices simultaneously) |
| Input range |
0 to ± 10 V dc, or 0 to ± 1000 V dc (with optional adapter), 1 reading/s |
| Scale factor |
Format: mx + b (gain and offset) user configurable |
| Displayed units |
User configurable (7 characters, for example, °C, psi, or m/s) |
| Wireless Bluetooth connection (check for availability) |
| Number of inputs |
2 |
| Supported modules |
Fluke Connect ® 3000 series |
| Acquisition |
1 reading/s |
| Environmental specifications |
| Operating temperature |
-25 °C to +50 °C (-13 °F to 122 °F)1 |
| Storage temperature |
Without battery: -25 °C to +60 °C (-13 °F to 140 °F), with battery: -20 °C to +50 °C (−4 °F to 122 °F) |
| Operating humidity |
IEC 60721-3-3: 3K6:
-25 °C to +30 °C (-13 °F to +86 °F): ≤ 100 %
40 °C (104 °F): 55 %
50 °C (122 °F): 35 % |
| Operating altitude |
2000 m (up to 4000 m derate to 1000 V CAT II/600 V CAT III/300 V CAT IV) |
| Storage altitude |
12,000 m |
| Enclosure |
IEC 60529: IP50
IEC 60529: IP65 with IP65 rated voltage connector |
| Vibration |
IEC 60721-3-3 / 3M2 |
| Electromagnetic compatibility (EMC) |
EN 61326-1: Industrial CISPR 11: Group 1, Class A
IEC 61000-6-5 Power station environment
Korea (KCC): Class A Equipment (industrial broadcasting and communication equipment)
USA (FCC): 47 CFR 15 subpart B. This product is considered an exempt device per clause 15.103 |