When utilized with a 50mm dolly, the PosiTest AT is in a priming state until reaching a priming pressure of 50 psi. It is only after the priming pressure is reached that the instrument begins calculating and displaying the pull rate. While it is possible to obtain readings below this priming pressure with the AT-M model, the AT-A automatic does not allow the operator to build priming pressure very slowly and is therefore not suitable for use below the priming pressure of 50 psi. Note that all reported adhesion values (including those obtained below the priming pressure) are subject to the PosiTest AT gage"s full-scale accuracy of ± 1% (± 30 psi, AT-M; ± 35 psi, AT-A).

I found this helpful (0)

Inaccurate? (0)

Answered by Anonymous

The 50 mm dolly is commonly recommended for use with concrete, wood and composite substrates, and measures coatings with expected adhesion values between 50 psi and 560 psi (50 - 500 psi for AT-M models). The 20 mm dolly is recommended for testing coatings applied to metals or with expected adhesion values greater than 500 psi.

I found this helpful (0)

Inaccurate? (0)

Answered by Anonymous

The versatile epoxy adhesive supplied with the PosiTest AT reaches full cure within 24 - 48 hours. Operators who require faster cure times should evaluate other adhesives for their compatibility with both the coating being tested and our aluminum test dolly. Cyanoacrylate ("super glue") type adhesives are often sufficient for lower pull-off strengths.

I found this helpful (0)

Inaccurate? (0)

Answered by Anonymous

The certified accuracy of both PosiTest AT models is identical. However, the fully automatic design of the PosiTest AT-A provides improved measurement consistency by eliminating the potential for operator influence from the test process.

I found this helpful (0)

Inaccurate? (0)

Answered by Anonymous

Absolutely. With an environmentally-sealed, metal enclosure, heavy-duty hydraulic pump and a high grade industrial pressure sensor, both the Manual and Automatic PosiTest AT are built to last. Weatherproof, dustproof and shockproof, they can be used indoors, outdoors and in all types of weather (meets or exceeds IP 65).

I found this helpful (0)

Inaccurate? (0)

Answered by Anonymous

The PosiTest AT arrives fully calibrated and ready to measure. A Long-Form Certificate of Calibration traceable to NIST or PTB is included, which documents actual readings taken by your instrument at our calibration laboratory on standards traceable to a national metrology institute. Beware of "Certificates" or "Certificates of Conformance" offered by competitors. These typically do not include actual instrument readings, and are often insufficient to meet common quality requirements.

I found this helpful (0)

Inaccurate? (0)

Answered by Anonymous

The rechargeable battery pack (user replaceable) in the PosiTest AT-A can perform over 200 tests on a single charge. Use the included AC adaptor to continue testing as the battery recharges.

I found this helpful (0)

Inaccurate? (0)

Answered by Anonymous

The PosiTest AT is supplied with self-aligning dollies that are precision-manufactured from strong and lightweight aluminum alloy (6061-T6). As a lower-cost alternative to steel loading fixtures, DeFelsko aluminum dollies are a single-use/consumable item and ideal for keeping as a permanent visual record of testing. For added utility and convenience, PosiTest AT-A Automatic models also include a handy shoulder strap and rubberized grips.

I found this helpful (0)

Inaccurate? (0)

Answered by Anonymous

No. Our instruments are designed for simple operation, feature easy-to-use menus, both full and quick instruction manuals, and helpful videos. In lieu of demonstration models, we provide unlimited technical support via telephone and/or email, and a limited 30-day money back guarantee.

I found this helpful (0)

Inaccurate? (0)

Answered by Anonymous

The ResinLab EP11HT epoxy adhesive supplied with the PosiTest AT is simple to use and suitable for testing a wide range of coating types. In some instances, specialized coatings will require a more specialized adhesive.

I found this helpful (0)

Inaccurate? (0)

Answered by Anonymous

Yes. Feedback from our customers is that the PosiTest AT gages are suitable for testing most internal or external pipe applications greater than 200 mm in diameter. In such cases, the maximum glue gap between the surface of the 20 mm dolly and the coating is 0.5 mm. For smaller pipe diameters, depending on the expected pull-off strength of the coating, it may be possible to use a 10 mm or 14 mm dolly. External diameters can be decreased to as low as 50 mm and 100 mm, for the 10 mm and 14 mm dollies, respectively. DeFelsko does do not provide or support the use of curved dollies for adhesion testing. In addition to affecting the surface area used in calculating pull-off strengths and the direction of the force lines (creating unwanted shear forces), most adhesion testing standards specifically call for the use of flat dollies.

I found this helpful (0)

Inaccurate? (0)

Answered by Anonymous

The PosiTest AT is designed for use with rigid, structural substrates. A flexible substrate can adversely impact test accuracy and repeatability. Furthermore, use of the PosiTest AT for measuring the adhesion of coatings applied to a brittle substrate typically results in the destruction of the substrate material, making it challenging to quantify the coating-substrate bond strength.

I found this helpful (0)

Inaccurate? (0)

Answered by Anonymous