| RFM3000 Series |
| Channels |
RFM3002 / RFM3002-GPIB - 2 channels; RFM3004 / RFM3004-GPIB - 2 channels |
| Display |
| Display Size |
5-inch WVGA multi-touch display with intuitive graphical user interface |
| Display Modes |
Graph (power vs time) - Numeric (numeric data) - Statistical measurements - CCDF |
| Automatic measurements (pulse, statistical, and marker measurements) |
| Marker Measurements (in Graph view) |
| Markers (vertical cursors) |
Settable in time relative to the trigger position |
| Marker Independently |
Avg, Min and Max Power at a specified time offset |
| Interval Between Markers |
Avg, Min and Max Power over the defined interval |
| Pair of Markers |
Ratio of power values at each marker |
| Pulse Mode |
| Automatic Measurements |
Pulse rise-time - Pulse fall-time - Pulse width - Pulse off-time - Pulse period - Pulse repetition frequency
Pulse duty cycle - Waveform average - Pulse peak - Pulse average - Pulse overshoot - Pulse droop
Top level power - Bottom level power - Edge delay - Pulse edge skew between channels |
| Statistical Mode |
| Automatic Measurements |
Peak power - Average power - Minimum power - Peak to average ratio - Dynamic range
Percent at cursor - Crest factor at cursor - Crest factor at various percents |
| Trigger |
| Synchronization |
Internal trig distribution |
| Mode |
Normal, Auto, Auto Pk-to-Pk, Free Run |
| Source |
Any connected RTP Series sensor (via SMB’s) or rear panel external trigger |
| Internal Level Range |
-40 dBm to +20 dBm (sensor dependent) |
| External Level Range |
± 5 volts or TTL |
| Slope |
+ or - |
| Hold-off, Min Pulse Width, Max Trigger Rate |
Sensor and timebase dependent |
| Time Base |
| Time Base Resolution, Range, Accuracy |
Sensor dependent |
| Time Base Display |
Sweeping or roll mode |
| Trigger Delay Range |
Sensor dependent |
| Trigger Delay Resolution |
0.02 divisions |
| Inputs/Outputs (front panel) |
| USB with SMB trigger port |
4 ports USB2.0: Type A receptacle, 4 ports SMB(f) |
Test Source
(optional rear panel placement) |
50 MHz |
1.00 mW (0 dBm) ± 2.3% (0.1 dB) typical |
| Inputs/Outputs (rear panel) |
| LAN |
10/100 Ethernet: RJ-45 modular socket |
| USB with SMB trigger port |
4 ports USB2.0: Type A receptacle, 4 ports SMB(f) |
| Multi I/O Connector |
User Selectable |
Status, trigger, or voltage output |
| Range |
0 to 10 V (Analog unipolar) |
| -10 V to +10 V (Analog bipolar) |
| 0 or 5 V (Logic) |
| Accuracy |
±200 mV (±100 mV typical) |
| Linearity |
0.4% typical |
| Remote Control |
| Command Set |
SCPI-1999.0 |
| LAN |
Ethernet: 10/100/1000 BaseT; HiSLIP |
| GPIB |
RFM3002 / RFM3004 - optional; RFM3002-GPIB / RFM3004-GPIB - included |
| Regulatory Compliance |
CE compliance with the following
European Union directives |
Low Voltage Directive: 2014/35/EU, RoHS Directive: 2011/65/EU,
WEEE Directive 2012/19/EU,
Electromagnetic Compatibility Directive (EMC): 2014/30/EU and
Environmental: MIL-PRF-28800F, Class 3 |
| General |
| Power Requirements |
90 to 260 VAC, 47 to 60 Hz; 90 to 135 VAC, 47 to 400 Hz; 30 W (35 VA) max |
| Operating Temperature |
0 to 50 °C (32 to 122 °F) |
| Storage Temperature |
-40 to +70 °C (-40 to 158 °F) |
| Humidity |
95% maximum, non-condensing |
| Altitude Operation |
up to 15,000 feet (4600 m) |
| Shock Withstands |
± 30 G, 11 ms impulse in X, Y, and Z axes |
| Vibration Withstands |
2 G sine, 5 to 55 Hz; 2 G random, 5 to 500 Hz |
| Warranty |
3 Years |
| Dimensions (excluding connectors) (H x W x D) |
3.5" x 8.3" x 11.2" (89 x 211 x 284 mm) |
| Weight |
4.8 lbs (2.2 kg) |
| Included Accessories |
Power cord |
| Optional Accessories |
RKRFM Full-width 19” Rack Mount Kit (includes handles & hardware for mounting one or two meters) |